Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 132
Search took 0.01 seconds.
Search: Posts Made By: Smog Tech
Forum: Model A (1928-31) 05-08-2019, 11:18 AM
Replies: 9
Views: 582
Posted By Smog Tech
Re: Fuel pump location question.

Nosetime, the motor part of the pump is about 2 inches from the header, the fuel part of the pump is about 5 inches from the header. I was concerned about heat and thought about adding a heat...
Forum: Model A (1928-31) 05-07-2019, 07:19 PM
Replies: 9
Views: 582
Posted By Smog Tech
Re: Fuel pump location question.

I use a Reds try-y Header. Holly fuel pump is mounted inside the right side frame rail. I use SAE J30R9 fuel hose from the tank to the pump and from the pump to the carburetors. On a hot day the...
Forum: Model A (1928-31) 05-07-2019, 08:34 AM
Replies: 11
Views: 624
Posted By Smog Tech
Re: Foaming Coolant

I have seen foaming when using modern "long life" antifreeze. The antifreeze made for cars 1989 and older seems to work much better in Model A's. You can find it in most auto parts stores.
Forum: Model A (1928-31) 01-31-2019, 05:21 PM
Replies: 12
Views: 1,164
Posted By Smog Tech
Re: Pressure Plate

Tom, great to see you back on the Barn.
Rick
Forum: Model A (1928-31) 01-16-2019, 11:58 PM
Replies: 16
Views: 1,068
Posted By Smog Tech
Re: Squealing engine

Had the same squeal with my engine. Spray the front crank seal with oil and squeal would go away, then return after a few hours running. Replaced with modern seal, no squeal and no leak.
Forum: Model A (1928-31) 01-05-2019, 11:14 PM
Replies: 30
Views: 2,760
Posted By Smog Tech
Re: Best Rear Main Seal

I have an "A" block with a "B" crank and rods. My pan is dimpled.
Forum: Model A (1928-31) 01-05-2019, 08:36 PM
Replies: 10
Views: 1,048
Posted By Smog Tech
Re: Non stock Muffler?

I use a 2" Hushpower 18" long muffler connected to a Reds Header. Works for me.
Forum: Model A (1928-31) 12-28-2018, 02:48 PM
Replies: 58
Views: 4,425
Posted By Smog Tech
Re: Tom Endy

Praying for a quick and complete recovery.
Rick
Forum: Model A (1928-31) 11-21-2018, 08:41 PM
Replies: 16
Views: 1,262
Posted By Smog Tech
Re: pressurized radiator work around

Not all pressure caps will work with an overflow tank. You need a pressure cap with two rubber gaskets, one to seal the pressure and one to seal the cap. You can remove the rubber gasket from the...
Forum: Model A (1928-31) 05-29-2018, 05:02 PM
Replies: 14
Views: 1,627
Posted By Smog Tech
Re: Radiator re-cored

Rick's is the place. He does very good work and knows old cars.
Forum: Model A (1928-31) 04-09-2018, 07:26 PM
Replies: 12
Views: 1,316
Posted By Smog Tech
Re: unusual head torque issue

I use ARP Ultra-Torque Assembly Lube on head nuts. Nuts don't stick to the threads.
I worried about the nuts loosening, but that a has not happened yet.
I torque Model A heads to 55 lbs.
Forum: Model A (1928-31) 03-15-2018, 07:45 PM
Replies: 31
Views: 2,511
Posted By Smog Tech
Re: Head Gasket

Flathead is correct, when you burn gasoline, water is a product of combustion.
The Best website says to use copper spray on their graphite head gaskets. I do and it works well.
Forum: Model A (1928-31) 03-08-2018, 05:53 PM
Replies: 96
Views: 7,583
Posted By Smog Tech
Re: Rear Panhard Bar ?

Denniskliesen: I see that you have washers under the bolt heads on the diff. The 3/8 SAE flat washers in the kit go between the bracket and the axle housing. If you have washers in both places,...
Forum: Model A (1928-31) 02-10-2018, 06:56 PM
Replies: 53
Views: 4,323
Posted By Smog Tech
Re: Replacement Ignition Coil

Bill,
On a MAC the Ω is option z.
Forum: Model A (1928-31) 02-09-2018, 11:36 PM
Replies: 53
Views: 4,323
Posted By Smog Tech
Re: Replacement Ignition Coil

I use an oil filled 1.5 Ω Pertronix Coil in my 6v Town Sedan. I do mount the coil with the high voltage terminal pointing up.
Forum: Model A (1928-31) 01-25-2018, 11:49 AM
Replies: 24
Views: 1,674
Posted By Smog Tech
Re: Best Anti-Freeze

Some in my Model "A" Club have had problems with Anti-Freeze foaming. I wonder if modern (Long Life) Anti-Freeze may foam in nonpressurized cooling systems. I use O'Reilly Anti-Freeze for older...
Forum: Model A (1928-31) 01-06-2018, 10:36 PM
Replies: 10
Views: 1,342
Posted By Smog Tech
Re: T 5 transmission for ModelA

The MAC'S bell housing from Australia is what I used on my Model 'A".
Forum: Model A (1928-31) 01-06-2018, 02:01 PM
Replies: 10
Views: 1,342
Posted By Smog Tech
Re: T 5 transmission for ModelA

I installed a T5 in my 1930 Town Sedan. I wanted a low first gear for parades, and not too tall 5th gear because I didn't think my mostly stock engine could pull it. The T5 from 4 cyl. S-10 would...
Forum: Model A (1928-31) 01-03-2018, 10:27 PM
Replies: 28
Views: 3,550
Posted By Smog Tech
Re: New B head.

I have a Winfield Red Head with the crowfoot chamber on my 1930 Town Sedan. Love that head.
Forum: Model A (1928-31) 12-28-2017, 08:22 PM
Replies: 13
Views: 1,582
Posted By Smog Tech
Re: Dual-exhaust header Model A

Reds also makes a very nice try-y header, have one on my 1930, like it.
Forum: Model A (1928-31) 12-28-2017, 08:18 PM
Replies: 3
Views: 575
Posted By Smog Tech
Re: Motor knocks

Pages 118 & 119 of the Service Bulletins shows how to drill the missing oil hole for the rear camshaft bearing in early blocks.
Forum: Model A (1928-31) 12-19-2017, 10:46 PM
Replies: 25
Views: 1,813
Posted By Smog Tech
Re: Stromberg 97 help

Check Float level on the Stromberg.
Forum: Model A (1928-31) 11-13-2017, 11:21 PM
Replies: 16
Views: 1,408
Posted By Smog Tech
Re: T5 adapter

I used a MAC Speed NZ, bell housing. Has peddle mounts and provision for the wish bone. No input shaft extension. Minimum cutting of the crossmember.
I used a Speedway open driveshaft conversion.
Forum: Model A (1928-31) 10-27-2017, 02:42 PM
Replies: 41
Views: 5,147
Posted By Smog Tech
Re: Hydraulic brakes

Early V8 Garage, Richard Lacy
1217 Azusa Canyon Road
West Covina, CA 91790
(626) 338-2282
Forum: Model A (1928-31) 10-27-2017, 08:26 AM
Replies: 41
Views: 5,147
Posted By Smog Tech
Re: Hydraulic brakes

It has been about 2 years sense I have been to Early V8 Garage. Some times when Richard is there by himself the doors will be closed, bang on the door and he will answer if he is there.
Showing results 1 to 25 of 132

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:02 PM.