Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 201
Search took 0.02 seconds.
Search: Posts Made By: Graham Freeman
Forum: Early V8 (1932-53) 05-08-2021, 03:37 PM
Replies: 7
Views: 379
Posted By Graham Freeman
Re: 1934 dual temperature gauge

Managed to get the red to rise to the half way point.
Have noticed a small bubble a couple of times in the red that disappeared with a slight tap to the gauge.
Am I expecting to much with just...
Forum: Early V8 (1932-53) 05-06-2021, 07:53 PM
Replies: 7
Views: 379
Posted By Graham Freeman
Re: 1934 dual temperature gauge

David,
The temperature part of the dual gauge is completely original.
I made a gauge from 3 originals of which I was able to use the original temp gauge and housing and swap the fuel gauge part...
Forum: Early V8 (1932-53) 05-06-2021, 04:43 PM
Replies: 7
Views: 379
Posted By Graham Freeman
1934 dual temperature gauge

I have a dual temperature gauge for my 34.
It has been hanging for some 18 months with the gauge portion at the top and the sender unit straight down below.
Upon testing it recently before I...
Forum: Early V8 (1932-53) 05-04-2021, 02:01 AM
Replies: 5
Views: 411
Posted By Graham Freeman
Re: 1933/34 radiator mounting pads.

Thanks David, that about matches what I have used.
The radiator is in now so will leave as is.
Graham
Forum: Early V8 (1932-53) 05-04-2021, 01:59 AM
Replies: 19
Views: 723
Posted By Graham Freeman
Re: intake valve seals??

Lawson, I think you will find that is the correct 1934 only oil filler tube, the cap however is a later year.
Forum: Early V8 (1932-53) 05-01-2021, 01:54 AM
Replies: 5
Views: 411
Posted By Graham Freeman
Forum: Early V8 (1932-53) 04-27-2021, 02:06 AM
Replies: 5
Views: 411
Posted By Graham Freeman
1933/34 radiator mounting pads.

I would like to know the approximate thickness of the rubber pads under the radiator mounts.
If someone could help before I install properly would be great as it must affect alignment of the hood....
Forum: Early V8 (1932-53) 04-14-2021, 03:59 PM
Replies: 27
Views: 1,051
Posted By Graham Freeman
Re: 1933/34 dual gauge temp sender unit (hose part).

David,
Did my email address get to you yesterday by PM?
Graham
Forum: Early V8 (1932-53) 04-12-2021, 09:46 PM
Replies: 14
Views: 545
Posted By Graham Freeman
Re: 33 Cabriolet window frame "support rod"

I had a similar problem with my cabriolet.
I replaced the rods with stainless steel and threaded the ends.
The nuts originally brass, can be turned from solid stock brass to get the 45 degree...
Forum: Early V8 (1932-53) 04-12-2021, 05:15 PM
Replies: 27
Views: 1,051
Posted By Graham Freeman
Re: 1933/34 dual gauge temp sender unit (hose part).

Thanks David,
Yes exactly what i am looking for.
Some close up pictures and dimensions would be great.
Regards
Graham Freeman
Forum: Early V8 (1932-53) 04-12-2021, 03:37 PM
Replies: 27
Views: 1,051
Posted By Graham Freeman
Re: 1933/34 dual gauge temp sender unit (hose part).

Thanks guys but I need details of the piece that takes the bulb that clamps into the hose.
Forum: Early V8 (1932-53) 04-11-2021, 11:03 PM
Replies: 27
Views: 1,051
Posted By Graham Freeman
Re: 1933/34 dual gauge temp sender unit (hose part).

Well I contacted Randy but he is out of stock and his supplier is closed due to Covid, I am not sure if it is temporary or for good.
So, is someone able to post or message me some close up picture...
Forum: Early V8 (1932-53) 04-10-2021, 03:04 AM
Replies: 27
Views: 1,051
Posted By Graham Freeman
1933/34 dual gauge temp sender unit (hose part).

Hi guys,
I am looking for the part on a 1933/34 dual gauge (new or used) that clamps thru the radiator hose that accepts the sender unit.
Are these being reproduced at all?
Thanks
Graham
Forum: Early V8 (1932-53) 04-02-2021, 03:50 AM
Replies: 7
Views: 551
Posted By Graham Freeman
Re: Conversion of Cutout to solid state

Hi Kevin,
Thanks for the response.
I had heard over the years that fitting a diode was supposed to help with charging when a radio was fitted, but I was a little doubtful and that is why I ask the...
Forum: Early V8 (1932-53) 04-02-2021, 12:24 AM
Replies: 7
Views: 551
Posted By Graham Freeman
Conversion of Cutout to solid state

I have a Diode conversion kit from Snyder's Auto Parts.
The instructions that came with it are for a round cutout.
I have an oval cut out and am wondering if anyone has done this adaption for an...
Forum: Early V8 (1932-53) 03-27-2021, 09:52 PM
Replies: 25
Views: 1,839
Posted By Graham Freeman
Re: Two rare 33-34 accessories?

1933/34 Ford speedo & 1933 instrument panel.
Forum: Early V8 (1932-53) 03-21-2021, 03:52 AM
Replies: 10
Views: 865
Posted By Graham Freeman
Re: Swap meets

One next Sat. in Winchester, they missed out last year because of C, so hopefully could be a good one.
Probably a bit far for most 'Barners' to go though.
Forum: Early V8 (1932-53) 03-21-2021, 03:48 AM
Replies: 33
Views: 1,596
Posted By Graham Freeman
Re: Inner Tubes for Radials?

Have you tried changing the backs for the fronts and see if they still loose air?
Forum: Early V8 (1932-53) 03-15-2021, 02:10 AM
Replies: 4
Views: 361
Posted By Graham Freeman
Re: 33/34 vacumn line/manifold nuts supply.

Thanks Kevin, I knew I had seen them listed somewhere but could not remember where.
Will contact him.
Graham
Forum: Early V8 (1932-53) 03-14-2021, 05:58 PM
Replies: 4
Views: 361
Posted By Graham Freeman
33/34 vacumn line/manifold nuts supply.

I am having trouble sourcing the correct brass nuts for fixing the vacumn lines into the manifold for a 1934 here in New Zealand.
These are the small ones 3/8".
I understand there are 3 sizes...
Forum: Early V8 (1932-53) 03-13-2021, 02:51 AM
Replies: 4
Views: 467
Posted By Graham Freeman
Re: 1933/34 exhaust question

David, Managed to pull the tailpipe out today and fit up the correct mount fixed to the back cross member.
Has eliminated the rattle problem.
Thankfully 0 miles on the motor so everything came...
Forum: Early V8 (1932-53) 03-09-2021, 03:49 PM
Replies: 8
Views: 405
Posted By Graham Freeman
Re: 34 armrests

So in this instance does it include cabriolet as a closed car?
Forum: Early V8 (1932-53) 03-09-2021, 02:54 PM
Replies: 6
Views: 658
Posted By Graham Freeman
Re: V-8 Times again

My Jan / Feb issue arrived this week in New Zealand.
However one local member has not got their Nov / Dec issue yet although does have the Jan / Feb issue.
Forum: Early V8 (1932-53) 03-09-2021, 02:50 PM
Replies: 4
Views: 467
Posted By Graham Freeman
Re: 1933/34 exhaust question

Thanks David, I have a clamp that appears to be the right one so will fit it up. Hopefully it will eliminate what may be a rattle problem against the chassis in that area. Easier to do now than when...
Forum: Early V8 (1932-53) 03-09-2021, 02:43 AM
Replies: 4
Views: 467
Posted By Graham Freeman
1933/34 exhaust question

Was the exhaust clamp/connection at the joint on the rear cross member fixed to the cross member or just a clamp for joining the 2 pieces of pipe together at this point.
There is a hole on my...
Showing results 1 to 25 of 201

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:54 PM.