Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: whiskeyding
Forum: Early V8 (1932-53) 09-26-2019, 11:00 PM
Replies: 10
Views: 942
Posted By whiskeyding
Re: Are all yellow top coils 12 volt

Thank you so much. I will look harder for markings mentioned. I looked but knowing they're there I will look again
Forum: Early V8 (1932-53) 09-25-2019, 07:52 PM
Replies: 10
Views: 942
Posted By whiskeyding
Are all yellow top coils 12 volt

Hello again,
I was on a job and a guy was going to junk a eac Mercury. I asked if I could save it and he said yes. I am now trying to determine if the coil and voltage regulator are 6 or 12 volts. ...
Forum: Early V8 (1932-53) 08-28-2018, 09:43 AM
Replies: 5
Views: 783
Posted By whiskeyding
Re: Bell systems truck

This is what I need
Forum: Early V8 (1932-53) 08-28-2018, 12:21 AM
Replies: 5
Views: 783
Posted By whiskeyding
Bell systems truck

Well hello again Ford barn. It has been a long time since I've posted anything, so long that I don't remember if I had ever done so. I have been working on this truck for most of my son's life. He...
Forum: Early V8 (1932-53) 07-21-2014, 11:20 PM
Replies: 6
Views: 982
Posted By whiskeyding
Re: 39-41backing plates still usable

Mr Texas I thank you that is the answer. After working on them again , the small clip in the first pic was just flattened. Once bent back the drivers side plate is good. Going to fabricate the...
Forum: Early V8 (1932-53) 07-17-2014, 04:30 PM
Replies: 6
Views: 982
Posted By whiskeyding
Re: 39-41backing plates still usable

Can I even buy these clips. I've found them for 42-48. But not 39-41 ??? Can I run with out them. Has any one
Forum: Early V8 (1932-53) 07-17-2014, 12:28 PM
Replies: 6
Views: 982
Posted By whiskeyding
39-41backing plates still usable

So hello fellas, in the process of getting my 39 pick up on the road I noticed that the hold down clips are all broken except one. Can these be replaced? I ask because they look like they ar e...
Forum: Early V8 12-18-2013, 09:48 PM
Replies: 1
Views: 600
Posted By whiskeyding
1935-40 frame section

Looking for a piece of frame to repair mine. Usual spot where x member meets outer rail . Drivers side.. Only about a foot long right where it kicks up. Thank you ford barn
Forum: Early V8 12-22-2011, 11:37 PM
Replies: 0
Views: 730
Posted By whiskeyding
1935-36 column drop parts

I need a couple column drop parts. Pretty much all of them. Cyl. no key is okay. ring with switch nail and on/off lever. On/off plate. cap for the end. bearing and spring for detent. and the...
Forum: Early V8 (1932-53) 04-07-2011, 09:11 PM
Replies: 8
Views: 5,714
Posted By whiskeyding
Re: Flathead Starter Brush Assembly???

I just took mine apart. If you push the brushes all the way up against the springs until they are pushing against the side of the brush they will stay there. Then once everything is assembled you...
Forum: Early V8 03-03-2011, 10:31 PM
Replies: 4
Views: 1,404
Posted By whiskeyding
1950-51 merc pass side water pump

Need a pass. side flathead merc water pump with to mounting tabs. not the 45* mounts. buildable core. have wide belt merc pump i'm willing to trade
Showing results 1 to 11 of 11

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:50 AM.