Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: The Master Cylinder
Forum: Model A (1928-31) 12-02-2021, 11:25 AM
Replies: 18
Views: 671
Re: Rear hub removal tool

There are ball bearings in the differential? I alway thought they were tapered roller bearings.
Forum: Late V8 (1954+) 11-13-2021, 02:08 PM
Replies: 68
Views: 1,718
Re: California pcv ??

They had factory PCV systems in 1955? I was not aware of that??
Forum: Model A (1928-31) 11-03-2021, 03:00 PM
Replies: 27
Views: 1,325
Re: Tubes for American Classic 19 inch radials

Are the tires that are available tubeless or does it make a difference?
Forum: Model A (1928-31) 10-13-2021, 10:39 AM
Replies: 41
Views: 2,389
Re: Consensus of opinion

IDK, I've seen my share of rectifiers go out.
Forum: Model A (1928-31) 09-27-2021, 03:32 PM
Replies: 14
Views: 858
Re: Proper Operating Temp?

What was the temperature when to engine was running. The temperature will always go up when then engine is just sitting there and not circulating after a drive. heat soak... I would say what you are...
Forum: Model A (1928-31) 09-23-2021, 07:00 PM
Replies: 43
Views: 3,127
Re: What's up with Macs/Ecklers

It is crazy out there, ships 'parked' off the coast of Port Los Angeles.

https://www.fordbarn.com/forum/attachment.php?attachmentid=474186&d=1632764615
Forum: Model A (1928-31) 08-29-2021, 11:22 AM
Replies: 21
Views: 1,843
Re: Vacuum Gauge (new)

At the risk of dragging this out farther but yes, Ryan did remove a post or two at the end.
Forum: Model A (1928-31) 08-16-2021, 04:51 PM
Replies: 25
Views: 1,981
Re: Engine RPMs

Ah, my bad. I misunderstood you. Low vacuum, high suction (high manifold pressure). High manifold pressure is not something I would normally measure or have a way to measure in my car. Maybe if I was...
Forum: Model A (1928-31) 08-16-2021, 09:16 AM
Replies: 25
Views: 1,981
Re: Engine RPMs

Not sure I agree with this statement, low manifold pressure would indicate lugging.
Forum: Model A (1928-31) 08-15-2021, 11:00 PM
Replies: 18
Views: 1,056
Re: Antifreeze yes or no?

I agree that people should try and search for answers to their question(s). Most topics have already been covered on Ford Barn over the years. Unfortunately I think Ford Barn has possibly the worst...
Forum: Model A (1928-31) 08-15-2021, 07:35 AM
Replies: 3
Views: 675
Re: Help Identify Carburator

Another recent thread.

https://www.fordbarn.com/forum/showthread.php?t=302249&highlight=marvel
Forum: Model A (1928-31) 08-11-2021, 03:36 PM
Replies: 14
Views: 575
Re: Pulling the Cylinder Head

That is way I said "Move or remove". Since he indicated he is working alone it would be better IMO to move the radiator forward and remove the water pump so it is easier to handle. But hey, what do I...
Forum: Model A (1928-31) 08-11-2021, 02:38 PM
Replies: 14
Views: 575
Re: Pulling the Cylinder Head

Do you belong to a club and do they have tools to loan out? A head puller is a great asset when removing a head.

Yes you can remove the head while in the car. But you will have to move or remove a...
Forum: Model A (1928-31) 08-11-2021, 02:31 PM
Replies: 21
Views: 1,982
Re: grease gun universal joint lube

The grease fitting is on the transmission rear bearing retainer and pointed directly at the u-joint. The torque tube bell and clam shells are back farther. There is nothing in the way of the lube...
Forum: Model A (1928-31) 08-11-2021, 10:12 AM
Replies: 21
Views: 1,982
Re: grease gun universal joint lube

I think we all know where the pumped in grease goes. The question is not so much where the NEW grease goes but where the OLD grease goes that the NEW grease replaces. I don't see it coming out...
Forum: Model A (1928-31) 08-07-2021, 09:35 AM
Replies: 15
Views: 1,142
Re: Valve clearance

First off let us start off by using the correct vernacular just so we are all clear. By 8000 to you mean .008" or .080"? 1300?

.008" is a little on the tight side while .080", as nkaminar...
Forum: Model A (1928-31) 08-06-2021, 07:37 PM
Replies: 11
Views: 737
Re: Water leak.

Well we ran the engine thru a couple of more heat cycles and re-torqued the head while it was hot. Yes I know, should torque when cold. But the seeping out the stud has stopped, for now.

We will...
Forum: Model A (1928-31) 08-05-2021, 11:25 PM
Replies: 11
Views: 737
Re: Water leak.

Yes, head was retorqued to 55 psi. Best gasket Graphtite gasket was used. I tried to pull the stud with no success. It has me baffled. I will update when we get the head off if we can determine the...
Forum: Model A (1928-31) 08-05-2021, 08:16 PM
Replies: 11
Views: 737
Water leak.

A couple of weeks ago we replaced a head gasket on my friends Model A. He just noticed water seeping out of the #3 stud (by the tightening sequence in the Red Book) or the 2nd one back on the drivers...
Forum: Model A (1928-31) 08-05-2021, 06:53 PM
Replies: 15
Views: 1,130
Re: cleaning parts

Evapo-rust?
Forum: Model A (1928-31) 08-05-2021, 06:45 PM
Replies: 28
Views: 1,805
Re: Inner tube advice needed

I gotta ask, did you check the inside of the tire? Maybe something is poking your tube.
Forum: Model A (1928-31) 08-05-2021, 12:28 PM
Replies: 8
Views: 610
Re: mystery message when trying to upload pics ???

There was just a thread on posting photos the other day. Easy to understand video. Thanks VeryTangled for sharing with us.

https://www.fordbarn.com/forum/showthread.php?t=301908
Forum: Model A (1928-31) 08-05-2021, 10:13 AM
Replies: 36
Views: 3,757
Re: Help diagnosing engine knock

Why is that? Is that true with all head gasket brands? In my examination all you gain by using a "B" gasket is two steam holes in the gasket that are not in the block or the head.
Forum: Model A (1928-31) 08-02-2021, 07:07 PM
Replies: 5
Views: 379
Re: Output Shaft Play

No, not normal. Start simple. Are you sure the bolt that holds the u-joint on is tight.
Forum: Model A (1928-31) 08-02-2021, 05:32 PM
Replies: 3
Views: 377
Re: Model A Day Vendor Registration

Thanks for clearing that up for me Mark.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:47 AM.