Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: Andy
Forum: Early V8 (1932-53) 04-16-2021, 02:54 PM
Replies: 5
Views: 248
Posted By Andy
Re: 1932 gas tank sending unit, passenger car

You should not have to remove the tank. The new sender should go thru the hole in the floor. There are baffles in the tank. You need to check for swing clearance with a piece of wire. I would run...
Forum: Early V8 (1932-53) 04-16-2021, 02:37 PM
Replies: 5
Views: 248
Posted By Andy
Re: 1932 gas tank sending unit, passenger car

I have put current production fuel gauges in two 32’s and on 45 pick up. I had no trouble with the float. I re-drilled the gauge flanges to match the tank holes. Maybe get another float.
Forum: Early V8 (1932-53) 04-15-2021, 03:32 PM
Replies: 11
Views: 230
Posted By Andy
Re: Need a source for '34 pitman arm for Heims

Regular tie rod ends have worked pretty good for a long time. I would weld on a salvaged boss and get rid of the ball but keep the arm. You get into a lot of stuff with splines, orientation, and...
Forum: Early V8 (1932-53) 04-13-2021, 07:21 PM
Replies: 4
Views: 312
Posted By Andy
Re: Crab distributor coil images

The coil mounts to sheet metal bracket mounted with the two forward drivers side intake bolts. I may have one. I sold the car I had one on.
Forum: Early V8 (1932-53) 04-13-2021, 01:29 PM
Replies: 12
Views: 583
Posted By Andy
Re: 1932 Ford Hudson steering box

Here are some pics. They are a much much better box than the F-1, F100, Hudson.
Forum: Early V8 (1932-53) 04-12-2021, 05:27 PM
Replies: 27
Views: 791
Posted By Andy
Re: 1933/34 dual gauge temp sender unit (hose part).

The common lower hose heater hose fitting looks similar. Maybe one could be modified?
Forum: Early V8 (1932-53) 04-12-2021, 10:59 AM
Replies: 12
Views: 583
Posted By Andy
Re: 1932 Ford Hudson steering box

The 37 Hudson steering box was only used in 37. The 47 Chevy pick up box was used thru 64 I think. It is basically the same as a 64 Impala box. It is recirculating like a Vega but many times stronger...
Forum: Early V8 04-08-2021, 06:27 PM
Replies: 2
Views: 335
Posted By Andy
Forum: Early V8 04-08-2021, 03:25 PM
Replies: 0
Views: 101
Posted By Andy
Original 32 front spreader bar

Original bar. It was bent and was straightened. It still need more work. It is still very slightly bent. It has dent also. The length is fine. I show it next to a bar in better shape. A little heat...
Forum: Early V8 04-08-2021, 03:10 PM
Replies: 0
Views: 77
Posted By Andy
1937-40 Ford Mercury jack

I believe this is an original 37-40 jack. I don't have the base or the lever. The base was just a stamped square with a depressed hole in the cnter. It is in very good shape It goes up and down just...
Forum: Early V8 (1932-53) 04-07-2021, 08:29 PM
Replies: 9
Views: 644
Posted By Andy
Re: Fuel pump just as a pass thru

Just leave it stock. I have used boost pumps running thru the stock pumps on many cars.
Forum: Early V8 04-07-2021, 04:49 PM
Replies: 1
Views: 178
Posted By Andy
Forum: Early V8 04-07-2021, 01:16 PM
Replies: 0
Views: 194
Posted By Andy
delete

delete
Forum: Early V8 04-05-2021, 02:25 PM
Replies: 2
Views: 335
Posted By Andy
Forum: Early V8 04-05-2021, 02:25 PM
Replies: 3
Views: 382
Posted By Andy
Forum: Early V8 04-04-2021, 06:59 PM
Replies: 0
Views: 95
Posted By Andy
33-3? Heavy duty oil bath air filter

Barn find type head mounted oil bath air filter. It has the original dirt! Looks to have pretty good original paint under the dirt. It is missing the two wing nuts and the hose is stiff and missing...
Forum: Early V8 04-04-2021, 06:32 PM
Replies: 1
Views: 178
Posted By Andy
32 Locking spare tire strap with key

Very rare 32 only locking spare tire strap with key. For rear spare tire mount. Sold before the locking hub cap came out. No rust. Works fine. Original key.
Forum: Early V8 (1932-53) 04-03-2021, 05:40 PM
Replies: 10
Views: 768
Posted By Andy
Re: From bad to worse

You can check low voltage resistance from the terminal on top to the spring contact on the bottom. It should be low ohms. Like 2-3. The high voltage windings are high ohms. It should be 10000 ohms or...
Forum: Early V8 (1932-53) 03-30-2021, 04:51 PM
Replies: 6
Views: 439
Posted By Andy
Re: 59AB valve train questions

Are the late lifters compatible with a 32 steel cam?
Forum: Early V8 (1932-53) 03-28-2021, 01:41 PM
Replies: 4
Views: 248
Posted By Andy
Re: 1934 steering column tube re-install

I would drill and tap the lock retaining pin and remove the lock. The lock has a code on the side and a locksmith can make a key from the code. He would not even need the lock
This is assuming the...
Forum: Early V8 (1932-53) 03-28-2021, 01:36 PM
Replies: 14
Views: 715
Posted By Andy
Re: 32 ford ooga horn

I looked into it a really long time ago. I think the solution was to move the mounting holes so the brushes were vertical. I am not at all sure that was the solution or the only problem.
Forum: Early V8 (1932-53) 03-28-2021, 09:20 AM
Replies: 38
Views: 2,472
Posted By Andy
Re: Deuce Heaven auction

Down. I can’t sell anything now. I gave away a extremely nice 5W. I put original parts up for sale and absolutely no interest.
Forum: Early V8 (1932-53) 03-25-2021, 05:50 AM
Replies: 3
Views: 357
Posted By Andy
Re: 1932 Ford 3 window upholstery kit

I bought material and had a local shop do the work. I took the seat cushions apart and re bagged the springs.
Forum: Early V8 03-01-2021, 05:03 PM
Replies: 3
Views: 382
Posted By Andy
Forum: Early V8 (1932-53) 02-25-2021, 12:27 PM
Replies: 25
Views: 1,500
Posted By Andy
Re: Brake drums

I don’t think the Speedway drums will work. The amount of flange outside the studs is less than Ford used. Stock Ford wheels will not have outside support.Compare the flange on the drum to the flange...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:31 AM.