Forum: Early V8
01-19-2021, 03:55 PM
|
Replies: 0
Views: 44
19 tooth speedometer gear parts for 3.78
Parts for a 19 tooth turtle (speerdo drive) for a 3.78 gear. Housing, shaft and retainer. The plug is still in the housing. I have a 18 tooth housing and parts and the heigth difference betheen the...
|
Forum: Early V8
01-19-2021, 03:39 PM
|
Replies: 0
Views: 34
|
Forum: Early V8
01-19-2021, 03:33 PM
|
Replies: 0
Views: 41
|
Forum: Early V8 (1932-53)
01-15-2021, 05:47 PM
|
Replies: 7
Views: 292
Re: 1932 Ford horn needing to make it 12 volt
I ran my 32 Spartan on 12 for many years with no complaint. I screwed the tension down so it would not overspeed. Later I put a beep horn on it.I had found a cheap aftermarket horn somewhere and the...
|
Forum: Early V8
01-15-2021, 12:42 PM
|
Replies: 4
Views: 313
|
Forum: Early V8
01-15-2021, 12:39 PM
|
Replies: 3
Views: 216
|
Forum: Early V8
01-14-2021, 06:58 PM
|
Replies: 0
Views: 82
Speedo 18 Tooth Housing
18 tooth speedo housing for 3.54 gear ratio rear ends. The shaft is there but the gear and cap are missing.
|
Forum: Early V8
01-14-2021, 05:38 PM
|
Replies: 0
Views: 76
33-36 license Plate Lens
Nice original lens. It has a small chunk out but would not show when installed. Look at pictures. It is not all scrached up. Marked 40-13445.
It is very thick and heavy. I really doubt the repos are...
|
Forum: Questions & Suggestions
01-13-2021, 10:28 PM
|
Replies: 3
Views: 309
|
Forum: Early V8 (1932-53)
01-13-2021, 07:56 PM
|
Replies: 6
Views: 265
|
Forum: Early V8
01-11-2021, 04:13 PM
|
Replies: 3
Views: 216
|
Forum: Early V8
01-11-2021, 04:10 PM
|
Replies: 4
Views: 313
|
Forum: Early V8
01-11-2021, 03:59 PM
|
Replies: 1
Views: 100
|
Forum: Early V8
01-08-2021, 05:58 PM
|
Replies: 1
Views: 100
32 Ford Front Hub Grease Retaining Baffle Rings
There are several designs of these small bolt pattern baffles used 32-36. These are original 32.
Fine shape except one has some light rust texturing on the outside bottom of one. Not thin anywhere....
|
Forum: Early V8
01-08-2021, 05:48 PM
|
Replies: 0
Views: 166
F-1 Drag Link
Really nice F-1 drag link. No rust or damage. One end has the small parts and the other is some of missing them. The parts kits are available for 15-20. The screw adjusters move as new. All it needs...
|
Forum: Early V8
01-08-2021, 05:35 PM
|
Replies: 0
Views: 218
|
Forum: Early V8
01-08-2021, 05:19 PM
|
Replies: 0
Views: 195
|
Forum: Early V8 (1932-53)
01-02-2021, 11:03 PM
|
Replies: 5
Views: 276
Re: Rebuilding a 36 steering gear
Notice that there is a keyway in the worm/shaft. You must have a driver with a recess to miss the keyway. The worm has the keyway and it fits into the slot in the shaft.
|
Forum: Early V8
01-02-2021, 04:25 PM
|
Replies: 0
Views: 112
|
Forum: Early V8
01-01-2021, 07:52 PM
|
Replies: 4
Views: 313
|
Forum: Early V8 (1932-53)
01-01-2021, 02:37 PM
|
Replies: 19
Views: 833
|
Forum: Early V8 (1932-53)
12-31-2020, 07:24 PM
|
Replies: 11
Views: 797
Re: Steering box light switch
You would need the 37-39 bottom plate with the brass tube. Your plate with the steel tube will not let the rod go thru. The rod is .380 or so. They are rolled and not completely round. There is an...
|
Forum: Early V8
12-31-2020, 04:41 PM
|
Replies: 0
Views: 133
|
Forum: Early V8
12-29-2020, 02:16 PM
|
Replies: 3
Views: 216
|
Forum: Early V8
12-29-2020, 02:14 PM
|
Replies: 4
Views: 313
|