Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: Drive Shaft Dave
Forum: Model A (1928-31) 07-30-2020, 10:29 PM
Replies: 8
Views: 1,319
Posted By Drive Shaft Dave
Re: Voltage Regulator??

I use Tom Wesenberg voltage reg, his is fool proof ,if the generator should go open circuit the voltage will remain low, not going into a self destruct high voltage runaway.
Forum: Model A (1928-31) 04-17-2020, 11:24 PM
Replies: 29
Views: 4,449
Posted By Drive Shaft Dave
Re: My Engine Project

Color looks good to me.:)
Forum: Model A (1928-31) 02-27-2020, 12:44 AM
Replies: 6
Views: 1,855
Posted By Drive Shaft Dave
Talking Re: Snow Coupe

She can't wait to get back in that coupe.:D
Forum: Model A (1928-31) 02-22-2020, 12:00 AM
Replies: 16
Views: 1,989
Posted By Drive Shaft Dave
Smile Re: Trunklid to tulip panel gap

Very interesting term, I had not heard that panel call the tulip panel before.:)
Forum: Model A (1928-31) 12-10-2019, 07:16 PM
Replies: 13
Views: 3,562
Posted By Drive Shaft Dave
Re: Replacing pistons

United Engine &Machine,Sil -Vo-Lite pistons,
Forum: Model A (1928-31) 12-06-2019, 02:16 PM
Replies: 52
Views: 5,993
Posted By Drive Shaft Dave
Re: Having Fun With it?

Looks like the spring on the bottom the oil pump is broken.
Forum: Model A (1928-31) 12-03-2019, 01:57 AM
Replies: 13
Views: 2,426
Posted By Drive Shaft Dave
Forum: Model A (1928-31) 10-26-2019, 11:06 PM
Replies: 19
Views: 3,292
Posted By Drive Shaft Dave
Re: Pan Gasket

looks good on paper, let us know the outcome.
Forum: Model A (1928-31) 10-05-2019, 11:15 PM
Replies: 13
Views: 2,629
Posted By Drive Shaft Dave
Re: New Two Blade Fan

Dont forget to use a thin flat washer under the shaft nut.
Forum: Model A (1928-31) 10-03-2019, 11:18 PM
Replies: 6
Views: 1,498
Posted By Drive Shaft Dave
Re: Tricks to remove cutout cover?

The idea is to break the spot welds there are usually two.
Forum: Model A (1928-31) 08-22-2019, 10:58 PM
Replies: 18
Views: 2,501
Posted By Drive Shaft Dave
Re: Motor Suddenly Stuck

This is one of those times when a block of wood and a very large whammer is your friend
...
Forum: Model A (1928-31) 08-17-2019, 11:07 PM
Replies: 14
Views: 2,240
Posted By Drive Shaft Dave
Re: New clutch - should the throw out bearing disengage?

Yes, if you are pushing the clutch pedal to the floor it will spin. how close is the throw out bearing when the pedal is released?
Forum: Model A (1928-31) 05-29-2019, 09:45 PM
Replies: 3
Views: 1,356
Posted By Drive Shaft Dave
Re: rear brake single shoe ,emerg brake history

In the case of the ModelA,the revised rear brakes came with a stepped drum to accomodate the emergency brake band. The early models simply picked up the service brake with the hand brake lever. As...
Forum: Model A (1928-31) 03-30-2019, 01:52 AM
Replies: 32
Views: 6,815
Posted By Drive Shaft Dave
Re: How much grease in the clamshell?

I just remove one of the bolts.
Forum: Model A (1928-31) 03-19-2019, 01:44 AM
Replies: 8
Views: 1,669
Posted By Drive Shaft Dave
Re: Trunk floor pan

The same part is used for both configurations.
Forum: Model A (1928-31) 02-27-2019, 01:31 AM
Replies: 10
Views: 2,270
Posted By Drive Shaft Dave
Re: Rear Hub Grease Seal Removal Tool

I have used the Tom Endy method for years , works good.
Forum: Model A (1928-31) 02-27-2019, 01:24 AM
Replies: 5
Views: 1,030
Posted By Drive Shaft Dave
Re: 31 Coupe Wood (Under side window)

upholstery panel nails to this.
Forum: Early V8 (1932-53) 02-02-2019, 08:34 PM
Replies: 11
Views: 1,839
Posted By Drive Shaft Dave
Re: What is this puller part for ???

The puller is used to remove rear drums and hub from tapered axle shafts. I didn't read the compete thread . I dont know what the other part is. Tried to delete but wouldn't take.
Forum: Model A (1928-31) 02-02-2019, 08:30 PM
Replies: 54
Views: 12,621
Posted By Drive Shaft Dave
Re: Ford Tri-Motor

Actually the Harvard was a different airplane, although a trainer with fixed gear.
Forum: Model A (1928-31) 02-01-2019, 09:10 PM
Replies: 12
Views: 2,169
Posted By Drive Shaft Dave
Re: Engine mount rubber replacement

Brattons cataloge pg. 35, 2018, shows motor mount rubbers made to the Ford print. while I have not tried these, the last mount 's I put in , made use of some dish soap and they slid in quite...
Forum: Model A (1928-31) 01-14-2019, 12:14 AM
Replies: 2
Views: 1,249
Posted By Drive Shaft Dave
Forum: Model A (1928-31) 01-07-2019, 12:24 AM
Replies: 48
Views: 9,960
Posted By Drive Shaft Dave
Re: Water Temperature Gauge

I have heard that the rex aco temp gauge has been problematic in the last few years .
Forum: Model A (1928-31) 01-07-2019, 12:09 AM
Replies: 8
Views: 2,972
Posted By Drive Shaft Dave
Re: Tom Wesenberg

Yes he is ok. just taking a look around the country side.
Forum: Model A (1928-31) 12-07-2018, 08:11 PM
Replies: 1
Views: 924
Posted By Drive Shaft Dave
Re: Need clarification...Bolts and Toggle Lever...

fine thread on the Spring Bolts, Toggle lever , drive in.
Forum: Model A (1928-31) 12-06-2018, 11:20 PM
Replies: 56
Views: 9,373
Posted By Drive Shaft Dave
Re: Weld and grind roller tracks

It is more of a hassle to replace them , weld then file or use die grinder.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:47 AM.