Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 18 of 18
Search took 0.01 seconds.
Search: Posts Made By: Binkman34
Forum: Early V8 (1932-53) 01-07-2018, 07:02 PM
Replies: 18
Views: 1,951
Posted By Binkman34
...................................

...................................
Forum: Early V8 01-06-2018, 06:03 PM
Replies: 0
Views: 300
Posted By Binkman34
1934 closed car windshield post section

I am trying to un-chop a 1934 Ford closed car and need about 6 inches of windshield post to do the job. I have all the material for the door posts and top.
Any leads appreciated.
-Thank you
Forum: Early V8 (1932-53) 12-10-2017, 04:55 PM
Replies: 0
Views: 261
Posted By Binkman34
1934 Ford Victoria Rear Bumper Extension Measurement

Does anyone have the approximate measurements of a 1934 Ford Victoria rear bumper extension ?
I need to fabricate a pair unless someone is reproducing them.
Thank you.
Forum: Early V8 (1932-53) 12-09-2017, 11:04 PM
Replies: 5
Views: 978
Posted By Binkman34
Re: Shipping a flathead

I used engine shippers.com.for a motor I purchased from Walt Dupont in Maine.
It was a few years ago but it cost 250.00 from Maine to Calif.
Forum: Early V8 12-08-2017, 01:39 AM
Replies: 2
Views: 722
Posted By Binkman34
Forum: Early V8 11-25-2017, 01:37 PM
Replies: 2
Views: 722
Posted By Binkman34
Forum: Early V8 (1932-53) 11-24-2017, 12:15 PM
Replies: 50
Views: 5,357
Posted By Binkman34
Re: Bob Drake sale

I tried to get '34 running boards, OUT OF STOCK
I tried to get a '34 grille OUT OF STOCK
I saved a lot more than 15% today !!
Forum: Early V8 (1932-53) 11-16-2017, 02:09 PM
Replies: 8
Views: 862
Posted By Binkman34
Re: What sieve size, glass bead media

I get mine at Harbor Freight. Their price for the media and shipping is much cheaper than anyone else I have found.
Harbor Freight # 61870
Forum: Early V8 (1932-53) 11-14-2017, 05:31 PM
Replies: 3
Views: 696
Posted By Binkman34
Does anyone reproduce '34 header panels ?

I am looking for a good '34 header panel.
Most of the '34 header panels I see for sale have rust issues.
I would think that someone has to be stamping these out by now.
Are any being repopped ?...
Forum: Model A (1928-31) 11-13-2017, 08:42 PM
Replies: 20
Views: 2,136
Posted By Binkman34
Re: Fastenal Shipping

Well, you did better than I did.
When I inquired about shipping at Fastenal they told me that in California they do not do freight shipments. I was a trying to ship an engine from the midwest to...
Forum: Early V8 (1932-53) 11-12-2017, 09:07 PM
Replies: 20
Views: 2,540
Posted By Binkman34
Re: 40 Ford Rear Axle Grease Seals

I have 6 of the seals left over from my convertible days.
I used 2 of them until I was able to tear into the rear axle.
The stopped the leak.
Forum: Early V8 11-08-2017, 02:21 PM
Replies: 2
Views: 722
Posted By Binkman34
1934 Ford Victoria front and rear seats

I am looking for a set of stock front and rear seats for a '34 Ford Victoria.
Thank you.
Forum: Early V8 (1932-53) 11-08-2017, 12:28 AM
Replies: 3
Views: 505
Posted By Binkman34
Re: '34 sedan and Victoria fenders

From what I was able to understand there is an oblong hole at the inner edge of the rear fender. It is not visible when the fender is mounted. I was told it is for the fuel filler pipe.
Forum: Early V8 (1932-53) 11-07-2017, 10:49 PM
Replies: 3
Views: 505
Posted By Binkman34
'34 sedan and Victoria fenders

I read where '34 sedan and Victoria rear fenders the same except for the lack of a hole in the fender for the fuel filler in the Victoria ?
Can anyone verify this ?
Forum: Early V8 11-07-2017, 07:43 PM
Replies: 0
Views: 337
Posted By Binkman34
Wanted : 1934 Ford drivers's side hood top

I am looking for a 1934 Ford drivers' side hood top.
Any leads appreciated.
Forum: Early V8 (1932-53) 10-31-2017, 05:03 PM
Replies: 18
Views: 1,517
Posted By Binkman34
Re: 33 ford with muncie

There was a munce M-21 in my 5-W coupe when I purchased it in the early '70's. It really made the car a blast to drive but it was not installed correctly. The crossmember was really butchered up to...
Forum: Early V8 (1932-53) 10-31-2017, 04:58 PM
Replies: 30
Views: 3,560
Posted By Binkman34
Re: What aftermarket turn signal do you recommend.

I have used the button type that Ron Francis sells as well.
You have to fabricate a bracket for them but they are out of the way, easy to get to, and trouble free.
Forum: Early V8 10-31-2017, 04:11 PM
Replies: 0
Views: 479
Posted By Binkman34
1934 Ford project body

I am looking for a '34 project car.
I have a lot of extra sheet metal and parts from previous projects and would like to put them to good use.
I am looking to see what might be out there for sale....
Showing results 1 to 18 of 18

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:45 AM.