Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: larrys40
Forum: Model A (1928-31) Yesterday, 08:06 PM
Replies: 11
Views: 477
Posted By larrys40
Forum: Model A (1928-31) 08-20-2019, 01:47 PM
Replies: 12
Views: 1,818
Posted By larrys40
Re: Brake Service Cross Shaft Reviews

Good synopsis review of pricing . If you don’t want to or can’t those prices are a bargain.
It can be difficult to get the coins and levers off and more time involved than what you think.
I gave...
Forum: Model A (1928-31) 07-25-2019, 06:47 AM
Replies: 20
Views: 1,179
Posted By larrys40
Re: Brake feel . . .

Dan
Glad to hear you bought a Model A but not on your brakes. Unless the rest of the car is top notch know that brakes on them to be done right and well can be expensive.
I’m giving the brake...
Forum: Model A (1928-31) 07-22-2019, 04:50 AM
Replies: 27
Views: 2,378
Posted By larrys40
Re: Hole in water jacket

I would carefully measure the depth of the hole vs the depth of the stud . Was a helicoil used? You could do a couple things.
One , use a small plug ( like a hardened threaded set screw) on the...
Forum: Model A (1928-31) 07-13-2019, 06:55 AM
Replies: 20
Views: 1,196
Posted By larrys40
Re: Rearching brake shoes.

Isn’t breathing illegal in California?

I do re-arching on all my brake jobs. Some say it isn’t necessary but I’ll err in the side it’s part of the details to making my brake jobs too notch and...
Forum: Model A (1928-31) 06-23-2019, 10:04 AM
Replies: 16
Views: 1,144
Posted By larrys40
Re: Fuel Gauge

I would try a heat gun to see if you can soften the old gas varnish that is probably still king the outer nut. At the point you donít care about the inner. Just the outer. I use an original 5z gas...
Forum: Model A (1928-31) 06-22-2019, 07:03 AM
Replies: 11
Views: 904
Posted By larrys40
Re: Dies at idle... Help

I agree it is most probable. Check carb bolts and intake exhaust gasket. Replacement is probably in order. Surface manifold if possible. Check rubber vacuum line for wiper . Plug manifold with 1/8...
Forum: Model A (1928-31) 06-14-2019, 07:19 PM
Replies: 3
Views: 785
Posted By larrys40
Re: How do I use this puller?

Rotowrench have a great description. Know that it will help break it loose but you will still have to pry it up and off the studs. It had alimited travel of the distance the studs are exposed till...
Forum: Model A (1928-31) 06-12-2019, 04:26 AM
Replies: 5
Views: 695
Posted By larrys40
Re: Transmission removal

I usually just remove the ujoint and there’s no need to remove the cross shaft. If you want to put the trans back in with u joint already installed then remove the cross shaft.

Larry shepard
Forum: Model A (1928-31) 06-09-2019, 02:51 PM
Replies: 5
Views: 371
Posted By larrys40
Re: 1931 slant windshield townsedan

Yes, Briggs . Ford had instructed both body manufactures to build them the same, unlike the previous models where Briggs and Murray had their own uniqueness .
Larry
Forum: Model A (1928-31) 06-07-2019, 11:46 PM
Replies: 13
Views: 827
Posted By larrys40
Re: 1932 drive shaft

Tom,
I just did one and am in the process of wrapping it up.
I concur witj the guys on the driveshaft. There were different varieties up to 36 with the 37 using the intermediate bearing.

If you...
Forum: Model A (1928-31) 06-07-2019, 11:40 PM
Replies: 9
Views: 861
Posted By larrys40
Re: block cleaning

You can physically remove it fairly easily and pry it out.Drill out what’s left where the journal Babbitt anchor holes are. They will be obvious .
Larry
Forum: Model A (1928-31) 06-02-2019, 07:10 AM
Replies: 10
Views: 957
Posted By larrys40
Re: Front brake repair on 31

As said above you will mess up threads if you don’t rotate the king pin /spindle bolt alittlw while moving the threaded stud end out of the spring perch. Looks like you need a full front end rebuild...
Forum: Model A (1928-31) 05-31-2019, 10:36 PM
Replies: 13
Views: 766
Posted By larrys40
Re: differential assembly

Jack,
Glad you found the issue. As said above it needs to be fully seated . If you take and old race or driver that can safely be used drive the bearing all the way down . You should not be able to...
Forum: Model A (1928-31) 05-31-2019, 10:24 PM
Replies: 7
Views: 449
Posted By larrys40
Re: Wagner Alternator Belt

I’ll add that usually tom Wagner’s alternators use a standard belt but I know there are some issues with some of the belts in the market fitting he pulleys and he says that. I will check with him...
Forum: Model A (1928-31) 05-30-2019, 10:35 PM
Replies: 6
Views: 563
Posted By larrys40
Re: Need electrical help

I agree with Brent on the intermittent short. A problem area that is very common is the reproduction terminal boxes. I always say they come with a potential built in short because the studs...
Forum: Model A (1928-31) 05-30-2019, 10:23 PM
Replies: 19
Views: 1,041
Posted By larrys40
Re: Paint for wheels

I generally use Sherwin williams 2nd dimension automotive paint. 4- coats.... is preferred but sometimes a good solid 3 will do it. paint jobbers in your area should be able to get a match or...
Forum: Model A (1928-31) 05-30-2019, 10:18 PM
Replies: 14
Views: 1,100
Posted By larrys40
Re: Cast Iron Drum temperaure too high??

Jim,
The temp gun is good for knowing which one is working the hardest .... but will at the initial break in be more than when they get settled in. Don't get too stuck on it. See how the skid...
Forum: Model A (1928-31) 05-30-2019, 10:09 PM
Replies: 13
Views: 766
Posted By larrys40
Re: differential assembly

I suspect the bearings are not driven on or are fully seated. This could be because they are not driven on fully, or because there is a burr on a carrier half ( or both). If you tried to use a...
Forum: Model A (1928-31) 05-28-2019, 02:45 PM
Replies: 6
Views: 493
Posted By larrys40
Re: How to remove blasted carrier bearings without ruining them

As Jim said a thin bearing remover should do it. You may have to modify it slightly to fit better. I am spoiled but grateful I have a full compliment of Kr wilson tools for the job. They make quick...
Forum: Model A (1928-31) 05-16-2019, 02:25 PM
Replies: 19
Views: 1,296
Posted By larrys40
Re: Radiator Recommendation

Bergs is not only a great cooling radiator but it fits perfectly. Gery is 2nd to none in my opinion. It might cost a little more but you will be more than pleased.
Larry Shepard
Forum: Model A (1928-31) 05-10-2019, 09:21 PM
Replies: 15
Views: 960
Posted By larrys40
Re: Drivetrain Locked Up

Good thought Benson. If he went to reverse and didn’t have OD locked out that would toast the overdrive planetaries. He didn’t advise of that and few run them but you never know.
Forum: Model A (1928-31) 05-10-2019, 07:49 AM
Replies: 7
Views: 467
Posted By larrys40
Re: Carb Inlet Valve

I was going to wait and see what others say here but am going to put my 2 cents in now in hopes of gaining feedback. I buy them about 10-20 at a time and find that only about 6 out of 10 hold vacuum...
Forum: Model A (1928-31) 05-09-2019, 08:09 PM
Replies: 14
Views: 917
Posted By larrys40
Re: Wards Riverside tires

I hate those tires but as you said they last a long time . I always say they wear like iron and drive like hell! They have to be 30 years old tho as they haven’t been made for about that long...
Forum: Model A (1928-31) 05-09-2019, 08:02 PM
Replies: 15
Views: 960
Posted By larrys40
Re: Drivetrain Locked Up

Bill
I would do a couple preliminary checks to help pinpoint what’s going on.
Pull the floorboard and pull the 6 bolts that hold the transmission shift tower into the top of the trans. Make sure...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:03 AM.