Forum: Early V8 (1932-53)
02-24-2023, 11:27 AM
|
Replies: 12
Views: 881
|
Forum: Early V8 (1932-53)
02-24-2023, 11:23 AM
|
Replies: 12
Views: 881
|
Forum: Early V8 (1932-53)
02-24-2023, 11:20 AM
|
Replies: 12
Views: 881
Re: tube shocks
tj, thank you for that info. auto stud,your info is very reasonable but in my sight doing it that way does'ent seam to line up with the top mount (in my line of sight}unless the top mount is...
|
Forum: Early V8 (1932-53)
02-23-2023, 01:26 PM
|
Replies: 12
Views: 881
Re: tube shocks
i looked up 1970's front shocks made by monroe and they are to short,there extended length is 14.63". my top to bottom or center to center is 17'.
|
Forum: Early V8 (1932-53)
02-22-2023, 07:55 PM
|
Replies: 12
Views: 881
tube shocks
i am converting my 46 mercury to tube shocks,i have mounted the upper front mount but did not drill the hole in the front axle yet. i checked the distance between top mount center and where i think...
|
Forum: Early V8 (1932-53)
02-20-2023, 01:07 PM
|
Replies: 4
Views: 649
16' inner tubes
i picked up some used 600x16 tires and plan on mounting them on 16"x4 1/2"rims with 600x16" tractor (implement tires) inner tubes, will this work?
|
Forum: Early V8 (1932-53)
02-14-2023, 07:36 PM
|
Replies: 17
Views: 1,588
Re: ignition lock cylinder
ok gents,did all you told me to do and it worked fine with some persuasion and juice the cylinder came out. could not get the key out so i took it to a local locksmith and he got the key out and made...
|
Forum: Early V8 (1932-53)
02-12-2023, 03:54 PM
|
Replies: 7
Views: 834
|
Forum: Early V8 (1932-53)
02-12-2023, 03:24 PM
|
Replies: 7
Views: 834
Re: rear brakes
would this be the marks you are talking about? See attached image.
|
Forum: Early V8 (1932-53)
02-10-2023, 10:26 AM
|
Replies: 17
Views: 1,588
|
Forum: Early V8 (1932-53)
02-10-2023, 10:21 AM
|
Replies: 7
Views: 834
rear brakes
i've got a question about the brakes on my 46 merc.they are all cleaned up and ready to put together.my question is,is there a position that the bottom cam #91a-2028 should be in,meaning the cam...
|
Forum: Early V8 (1932-53)
02-09-2023, 11:23 AM
|
Replies: 17
Views: 1,588
|
Forum: Early V8 (1932-53)
02-09-2023, 11:20 AM
|
Replies: 17
Views: 1,588
|
Forum: Early V8 (1932-53)
02-09-2023, 11:06 AM
|
Replies: 17
Views: 1,588
|
Forum: Early V8 (1932-53)
02-07-2023, 04:51 PM
|
Replies: 17
Views: 1,588
|
Forum: Early V8 (1932-53)
02-07-2023, 02:12 PM
|
Replies: 17
Views: 1,588
ignition lock cylinder
i have a 46 mercury with key broke off in cylinder, under the cylinder there are two (looks like pins)one is about 1/16"od and the other is about 1/4"od. are they threaded or pressed in pins? my...
|
Forum: Early V8 (1932-53)
01-18-2023, 01:04 PM
|
Replies: 7
Views: 963
Re: 46 mercury clutch and brake peddle springs
hey guys thank you all for the great info and pictures,bruce sent me some pictures showing clutch spring from pivot pin to hole in lower brace below the master cyl.the brake spring goes from pivot...
|
Forum: Early V8 (1932-53)
01-14-2023, 10:27 PM
|
Replies: 7
Views: 963
|
Forum: Early V8 (1932-53)
01-14-2023, 09:54 PM
|
Replies: 7
Views: 963
46 mercury clutch and brake peddle springs
does anyone have pictures of the brake and clutch peddle spring location from pin #7533toother end of spring on a 1946 mercury or ford that you can share. any information will help. thank you
|
Forum: Early V8 (1932-53)
11-22-2021, 10:22 AM
|
Replies: 4
Views: 5,800
Re: Dash board trim
rotorwrench, thank you for that info.i have seen the metal one on a merc but it just does not look right.so,i don't know just yet what to do.thank you both for the info.if any new info comes up...
|
Forum: Early V8 (1932-53)
11-21-2021, 10:18 AM
|
Replies: 4
Views: 5,800
Re: Dash board trim
bill,i don't have any pictures,there is a difference in the design of the two.the parts needed are the trim over the speedo,the center grill and clock trim.i am trying to find out if the mounting...
|
Forum: Early V8 (1932-53)
11-20-2021, 08:45 AM
|
Replies: 4
Views: 5,800
Dash board trim
Will 1946 ford dash board trim fit in a 1946 mercury dashboard
|
Forum: Early V8 (1932-53)
02-26-2021, 02:47 PM
|
Replies: 7
Views: 983
windshield seal on a 46
hey guys and girls,i am looking to purchace a windshield seal for my 46 merc with trim and looking at mac's it shows one with a price of $65.00. has anyone ever used this seal and it worth the price...
|
Forum: Early V8 (1932-53)
02-25-2020, 06:19 PM
|
Replies: 12
Views: 2,062
Re: crank shaft pully
jm,thank you for that information.a local friend found one in his barn and gave it to me. so im all set.thank you all for your time, efforts and great information,john
|
Forum: Early V8 (1932-53)
02-21-2020, 05:30 PM
|
Replies: 12
Views: 2,062
Re: crank shaft pully
thanks for the pix,JM your picture is the one i am interested in.can you measure the distance from center to center of the sheaves and do you have one for sale?
|