Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 225
Search took 0.01 seconds.
Search: Posts Made By: mrlaser
Forum: Early V8 12-21-2021, 09:30 AM
Replies: 1
Views: 119
Posted By mrlaser
Re: 1951 Ford convertible interior stainless trim

This is the back side of the above trim piece. I was unable to upload with original post.
Forum: Early V8 12-21-2021, 09:23 AM
Replies: 1
Views: 119
Posted By mrlaser
1951 Ford convertible interior stainless trim

This is an NOS passenger side stainless trim piece for the original door panel. The attached picture of the door panel is for reference only. The door panel is not included in the sale. Shipping cost...
Forum: Early V8 (1932-53) 11-24-2021, 06:16 PM
Replies: 11
Views: 1,176
Posted By mrlaser
Re: 50 Ford Caster and Camber bushing tools 3089-N, 3046-N

BTW, would anyone know what size wrench(s) is/ are necessary for adjusting the upper and lower eccentric bushings? I don't have current access to measure them myself. Thanks for any additional help.
Forum: Early V8 (1932-53) 11-24-2021, 05:04 PM
Replies: 11
Views: 1,176
Posted By mrlaser
Re: 50 Ford Caster and Camber bushing tools 3089-N, 3046-N

That's a great suggestion. It can be made thin enough if necessary. Thanks
Forum: Early V8 (1932-53) 11-22-2021, 10:40 AM
Replies: 11
Views: 1,176
Posted By mrlaser
Re: 50 Ford Caster and Camber bushing tools 3089-N, 3046-N

I know this is an old thread but I have not been able to find the wrench size needed to fabricate the above mentioned tools. Could anyone provide sizes and any suggestions regarding these tools? Also...
Forum: Early V8 (1932-53) 06-04-2021, 07:11 AM
Replies: 10
Views: 577
Posted By mrlaser
Re: 51 Victoria 3 piece rear glass install?

We did the bottom lip first then worked around to the top. The whole process of setting the glass took about 40-50 min. Putting all three pieces in the rubber made the whole structure somewhat...
Forum: Early V8 (1932-53) 06-03-2021, 12:12 PM
Replies: 10
Views: 577
Posted By mrlaser
Re: 51 Victoria 3 piece rear glass install?

The stainless perimeter pieces went on first, followed by the 2 vertical stainless pieces. The actual glass instillation was definitely a two person job. One on the inside pulling the cord to engage...
Forum: Early V8 (1932-53) 06-01-2021, 10:21 AM
Replies: 10
Views: 577
Posted By mrlaser
Forum: Early V8 (1932-53) 06-01-2021, 10:19 AM
Replies: 10
Views: 577
Posted By mrlaser
Re: 51 Victoria 3 piece rear glass install?

The picture in my previous post shows the passenger side glass in place. Later this was removed and the center window put in place initially. I posted the picture from my phone and meant to show the...
Forum: Early V8 (1932-53) 06-01-2021, 06:48 AM
Replies: 10
Views: 577
Posted By mrlaser
Re: 51 Victoria 3 piece rear glass install?

I did my install in 3 individual pieces. The center section first followed by the side windows. That is different than what was described in the accompanying instructions which recommended putting...
Forum: Early V8 (1932-53) 04-05-2021, 10:52 AM
Replies: 50
Views: 4,980
Posted By mrlaser
Exclamation Re: USPS damage in shipping

I have have had so many issues in the past with the USPS. Never the less, I recently decided to use Priority Express with a guarantee of 1-2 days shipping to an address 340 miles away thinking that...
Forum: Early V8 (1932-53) 03-10-2021, 12:35 PM
Replies: 8
Views: 1,167
Posted By mrlaser
Re: Vin location on a 1951 Ford Custom Deluxe Club Coupe

This is on the passenger side front top rail
Forum: Early V8 (1932-53) 03-10-2021, 12:33 PM
Replies: 8
Views: 1,167
Posted By mrlaser
Re: Vin location on a 1951 Ford Custom Deluxe Club Coupe

The serial number is stamped on the frame rail in a couple of places. It matched the number on the firewall plate on my car.
Forum: Early V8 (1932-53) 03-07-2021, 12:27 PM
Replies: 42
Views: 4,759
Posted By mrlaser
Re: Charlie stolded.....my version

The following is an email that I sent to Charlie after he restored my previously "restored 94" which had been done by another very large early Ford parts supplier but never functioned properly.

...
Forum: Early V8 (1932-53) 03-07-2021, 07:42 AM
Replies: 49
Views: 3,800
Posted By mrlaser
Re: Rebuilt starter

Just wondering: The Rock Auto starter lists the battery voltage as 12.6 volts.
Forum: Early V8 (1932-53) 02-26-2021, 11:50 AM
Replies: 23
Views: 1,658
Posted By mrlaser
Re: Drive through Chicago in the early Forties

It also looks as though "jaywalking" was the national pastime.
Forum: Early V8 (1932-53) 02-24-2021, 01:04 PM
Replies: 83
Views: 6,201
Posted By mrlaser
Re: Trouble shoot 1950 8Ba initial start up Help

Another thing to consider, in addition to those ideas already mentioned, is the primary resistance in the coil. This is assuming that you have retained the original 6 volt system. The coils sold by...
Forum: Early V8 (1932-53) 02-08-2021, 03:36 PM
Replies: 8
Views: 760
Posted By mrlaser
Re: 1951 Ford Victoria Headliner

I should have said that the correct way includes removing the rear window. I suppose the cloth headliner could be glued but it would be difficult to get the necessary stretch for a nice fit.
Forum: Early V8 (1932-53) 02-08-2021, 12:40 PM
Replies: 8
Views: 760
Posted By mrlaser
Re: 1951 Ford Victoria Headliner

I was referring only to the 1951 Ford Victoria in the above post. The headliner, in this instance, does in fact need to be installed with the glass removed. On other models, that may not be necessary.
Forum: Early V8 (1932-53) 02-04-2021, 11:32 AM
Replies: 8
Views: 760
Posted By mrlaser
Re: 1951 Ford Victoria Headliner

One other thing to keep in mind is that to replace the headliner you need to remove and replace the three piece rear window. Been there, done that. It is a bit of a challenge.
Forum: Early V8 (1932-53) 02-04-2021, 11:13 AM
Replies: 8
Views: 760
Posted By mrlaser
Re: 1951 Ford Victoria Headliner

This is the headliner in my '51 Victoria. It is very close to the one in the Victoria that I had as a teenager. Both cars were two tone green. Unfortunately, it was purchased from the now bankrupt...
Forum: Early V8 (1932-53) 01-30-2021, 06:19 PM
Replies: 15
Views: 1,482
Posted By mrlaser
Re: Chrome Shop Recommendations

I used Jon Wright Custom Chrome Plating ,Grafton Ohio for a 1954 Corvette. Show car quality but $$$$. I have used Bumper Boyz in California for nice, but somewhat lower quality and far fewer $.
Forum: Early V8 01-21-2021, 05:34 PM
Replies: 2
Views: 233
Posted By mrlaser
Forum: Early V8 (1932-53) 01-18-2021, 12:44 PM
Replies: 9
Views: 770
Posted By mrlaser
Re: 3 spd OD 12v solenoid

Sorry, that's Vintage Auto Garage.
Forum: Early V8 (1932-53) 01-18-2021, 12:42 PM
Replies: 9
Views: 770
Posted By mrlaser
Re: 3 spd OD 12v solenoid

Vintage Auto Supply Has twelve volt solenoids
Showing results 1 to 25 of 225

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:46 PM.