Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 289
Search took 0.02 seconds.
Search: Posts Made By: OHV DeLuxe
Forum: Early V8 (1932-53) 11-27-2020, 04:57 AM
Replies: 1
Views: 222
Posted By OHV DeLuxe
Canadian rod bearing part number.

I have a box of rod bearings with part number C39T-6211-A.
It also says LV7FD/Can.
Can anyone tell me what that is for?

Thanks.
Forum: Early V8 (1932-53) 11-24-2020, 04:35 AM
Replies: 2
Views: 332
Posted By OHV DeLuxe
59a oil pump capacity.

I have pulled apart a 59a engine to control everything and replace a few parts.
Story on the engine is that it was NOS up until 1989, put into a 1939 pu and driven very little for about 10 years...
Forum: Model A (1928-31) 06-30-2020, 12:42 PM
Replies: 3
Views: 547
Posted By OHV DeLuxe
Re: G28T center cam bearing oiling?

Hi Jim! I was thinking about filing like that too, i see no way it will get pressure otherwise.
Forum: Model A (1928-31) 06-30-2020, 10:28 AM
Replies: 3
Views: 547
Posted By OHV DeLuxe
G28T center cam bearing oiling?

I now have my rebuilt G28T block and bottom end on the bench, and as always i go through the oil passage system.
These are as some of you know full pressure B type block, they have a solid top oil...
Forum: Early V8 (1932-53) 01-24-2020, 03:50 AM
Replies: 22
Views: 1,761
Posted By OHV DeLuxe
Re: How do I get pressure plate out.

Use the 3/8" ratchet set and there is a small radius on the top of the opening in the block allowing the ratchet extender to reach the bolts pretty straight on. Then you should be able to "walk" the...
Forum: Early V8 (1932-53) 01-30-2019, 04:09 AM
Replies: 50
Views: 6,673
Posted By OHV DeLuxe
Re: Want o go highway speeds ??? Need opinions.

I had a 48 running hot all the time, rebuilt and advanced the ign 2 degrees, still hot,
then i ran 50/50 white vinegar and water for one day around the backroads, in the afternoon bottom tap was...
Forum: Early V8 (1932-53) 10-10-2018, 03:53 AM
Replies: 2
Views: 592
Posted By OHV DeLuxe
1942-48 distributor parts.

Hi, i need to find a source for 1942-48 distributor tiny wire connector rubber boot and slotted nut, either nos or new. is this available anywhere? thanks.
Forum: Early V8 10-10-2018, 03:19 AM
Replies: 2
Views: 907
Posted By OHV DeLuxe
Forum: Early V8 09-04-2018, 02:47 AM
Replies: 1
Views: 558
Posted By OHV DeLuxe
Forum: Early V8 (1932-53) 08-30-2018, 03:13 AM
Replies: 8
Views: 1,460
Posted By OHV DeLuxe
Re: V8 lockable gas cap.

Ok thanks! that is what i thought, cool looking though, thank you for sharing your knowledge.
Forum: Early V8 (1932-53) 08-29-2018, 07:23 AM
Replies: 8
Views: 1,460
Posted By OHV DeLuxe
V8 lockable gas cap.

Who made this very cool V8 locking gas cap? The key and cylinder is Star brand.
I suppose it is an aftermarket item? i have not seen this type before.
Forum: Early V8 (1932-53) 08-28-2018, 05:19 AM
Replies: 9
Views: 1,571
Posted By OHV DeLuxe
Forum: Early V8 08-28-2018, 04:20 AM
Replies: 0
Views: 488
Posted By OHV DeLuxe
Looking for a set of Jax lifters for Flathead V8

Looking for a set of Jax lifters for Flathead V8,
I cannot get a hold of the Jax company and would like to buy a set of these lifters.
Who stocks these?
Thanks.
Forum: Early V8 (1932-53) 08-27-2018, 02:36 AM
Replies: 16
Views: 4,668
Posted By OHV DeLuxe
Re: Stromberg eFire Dizzy

I agree, i rebuild, test and run the 1942-48 "crab" distributor, for people and myself.
It`s hard to see any gains in this new unit, why replace the best distributor ever made for a modern unit...
Forum: Early V8 (1932-53) 08-12-2018, 01:37 PM
Replies: 4
Views: 861
Posted By OHV DeLuxe
Forum: Early V8 (1932-53) 08-12-2018, 12:53 PM
Replies: 4
Views: 861
Posted By OHV DeLuxe
Three ring pistons, where do i find rings.

I hava a set of nos std size three ring pistons with regular wide ring grooves, where do i find rings? Thanks!
Forum: Early V8 02-27-2018, 09:09 AM
Replies: 1
Views: 558
Posted By OHV DeLuxe
WTB shortened and resplined Cad/LaSalle output shaft for Ford torque tube.

Looking for a shortened and resplined Cad/LaSalle output shaft for Ford torque tube.
Thanks!
Forum: Early V8 (1932-53) 02-09-2018, 04:42 AM
Replies: 61
Views: 9,140
Posted By OHV DeLuxe
Re: Coil deal!!

Tried to buy four but unfortunately they will not ship outside US.
Forum: Early V8 01-15-2018, 04:57 AM
Replies: 0
Views: 579
Posted By OHV DeLuxe
2" Winfield D Downdraft and 2" Riley sidedraft.

Looking for a number two of these two carburetors.
2" Winfield D Downdraft and 2" Riley sidedraft.
Any leads are appreciated.
I have other interesting carburetors and ignition systems for trade...
Forum: Model-A 01-15-2018, 04:54 AM
Replies: 0
Views: 512
Posted By OHV DeLuxe
2" Winfield D Downdraft and 2" Riley sidedraft

Looking for a number two of these two carburetors.
2" Winfield D Downdraft and 2" Riley sidedraft.
Any leads are appreciated.
I have other interesting carburetors and ignition systems for trade...
Forum: Early V8 (1932-53) 10-31-2017, 03:46 AM
Replies: 88
Views: 9,381
Posted By OHV DeLuxe
Re: Condenser Capacitiance.

This is our test equipment. 1940s VLC (european KRW) from a local Ford shop still works wonderfully, Serial resistance, leakage and capitance. 220 volts.
The other tester is for coils.
Forum: Early V8 (1932-53) 10-20-2017, 07:15 AM
Replies: 14
Views: 1,913
Posted By OHV DeLuxe
Re: Closed PCV System for my C69A

I would look at the WW2 Ford and Willys Jeeps for well functioning and era correct way to do it.
Forum: Early V8 (1932-53) 09-28-2017, 03:57 AM
Replies: 1
Views: 437
Posted By OHV DeLuxe
1937-48 truck water pumps disassembly.

How to i disassemble 1937-48 truck water pumps?
I`m used to the regular water pumps with bronze bushing, and they come apart real easy in a press.
Hard to tell if the bearing is locked into the...
Forum: Early V8 09-12-2017, 05:30 AM
Replies: 2
Views: 907
Posted By OHV DeLuxe
Forum: Model A (1928-31) 09-10-2017, 02:09 PM
Replies: 3
Views: 863
Posted By OHV DeLuxe
Showing results 1 to 25 of 289

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:36 PM.