Forum: Model A (1928-31)
09-08-2020, 10:25 PM
|
Replies: 4
Views: 255
|
Forum: Model A (1928-31)
09-07-2020, 02:40 PM
|
Replies: 2
Views: 275
|
Forum: Model A (1928-31)
09-07-2020, 02:26 PM
|
Replies: 4
Views: 255
Clutch shaft AA and A the same?
I believe the clutch shaft pin broke or sheared inside the bell housing on my 1928 AA 4 speed transmission. Is the shaft the same as the model A 3 speed shaft? Are the bushings the same?
I would...
|
Forum: Model A (1928-31)
04-15-2020, 10:51 AM
|
Replies: 8
Views: 1,365
Re: Model a trader
Maybe they passed away but the server is still connected to some other business.
|
Forum: Model A (1928-31)
04-01-2020, 04:02 AM
|
Replies: 18
Views: 4,493
Re: 7 tooth steering box
This is a video I made replacing the bushings in my 7 tooth steering box while still in the Pickup.
https://m.youtube.com/playlist?list=PLav-W1BC-Nj9nDx7S_Z1kpxH2TLliMjIX
|
Forum: Model A (1928-31)
03-29-2020, 04:36 AM
|
Replies: 6
Views: 959
Re: Mutant B Carb
Most likely it is a Zenith Carburetor from a tractor. Tractors usually don’t have the GAV.
|
Forum: Model A (1928-31)
03-16-2020, 03:08 PM
|
Replies: 1
Views: 435
|
Forum: Model A (1928-31)
03-16-2020, 03:06 PM
|
Replies: 1
Views: 435
|
Forum: Model A (1928-31)
03-02-2020, 02:04 PM
|
Replies: 31
Views: 2,441
|
Forum: Model A (1928-31)
02-26-2020, 01:14 PM
|
Replies: 8
Views: 857
Re: rear axle taper/threads
No shims unless someone added them because the hub rubbed the backing plate.
If you find shims then the taper most likely has some wear. I have shims on my axles to prevent the hubs from rubbing the...
|
Forum: Model A (1928-31)
02-26-2020, 12:52 PM
|
Replies: 8
Views: 857
Re: rear axle taper/threads
Normally when torqued correctly to 100lbs it will stay tight. It will be so tight that it will require a puller to break it loose.
Once it becomes loose while driving and un noticed the taper will...
|
Forum: Model A (1928-31)
02-25-2020, 05:40 PM
|
Replies: 20
Views: 1,174
Re: Tappet(lifter) Noise
There is a good chance that you are hearing the valves beginning to stick. If you ran any old fuel thru it the valves will start to stick. I'd run a tank of fuel thru the engine while driving it with...
|
Forum: Model A (1928-31)
02-22-2020, 05:13 PM
|
Replies: 13
Views: 1,327
Re: Hand throttle notches
You can weld up the worn away area then carefully grind or file the raised edge to fit into the grooves.
|
Forum: Early V8
02-22-2020, 01:28 PM
|
Replies: 15
Views: 1,532
Re: Fullrace Flathead Buildup on DVD
[QUOTE=Fullraceflathead;1823146]The Video I made back in 1996 during the Build Up of the "Fullrace Flathead" Supercharged 296 Engine that I built for my Front Engine Nostalgia Dragster "Bad Moon...
|
Forum: Model A (1928-31)
02-17-2020, 05:24 PM
|
Replies: 18
Views: 1,362
|
Forum: Model A (1928-31)
02-14-2020, 05:21 PM
|
Replies: 10
Views: 892
|
Forum: Early V8
02-13-2020, 03:56 PM
|
Replies: 15
Views: 1,532
|
Forum: Model A (1928-31)
02-09-2020, 04:06 PM
|
Replies: 16
Views: 1,511
|
Forum: Model A (1928-31)
02-09-2020, 02:41 PM
|
Replies: 16
Views: 1,511
|
Forum: Model A (1928-31)
02-09-2020, 02:39 PM
|
Replies: 16
Views: 1,511
Re: San diego big 3 swap meet--last one
I’ve not been impressed with this event when it comes to finding Model A items for the last 5 years. The Pomona Swap meet is much bigger and it also has small amount of Model A sellers.
In my...
|
Forum: Early V8
01-23-2020, 09:40 PM
|
Replies: 15
Views: 1,532
Re: Fullrace Flathead Buildup on DVD
https://www.ebay.com/itm/Ford-V8-Isky-404-Flathead-V8-296-Fullrace-Flathead-Ford-Engine-Build-Up-DVD/324049807339?hash=item4b72dfa7eb:g:AVQAAOSwN2ZdIUzS
|
Forum: Early V8
01-23-2020, 04:16 PM
|
Replies: 15
Views: 1,532
|
Forum: Model A (1928-31)
12-22-2019, 01:51 AM
|
Replies: 4
Views: 836
Re: front timing cover
Could it have been used in the aircraft version of the Model A Engine? Those engines used a Magneto and no front mount I believe.
|
Forum: Model A (1928-31)
12-14-2019, 04:46 PM
|
Replies: 18
Views: 1,419
|
Forum: Model A (1928-31)
11-27-2019, 10:11 PM
|
Replies: 4
Views: 1,435
|