Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 22 of 22
Search took 0.00 seconds.
Search: Posts Made By: mhaim
Forum: Early V8 (1932-53) 08-23-2020, 02:50 PM
Replies: 20
Views: 974
Posted By mhaim
Re: Which is easier

I do like the idea of pulling the engine. I can do almost the whole thing standing up. And once itís out I can do some touch up in the engine bay. Thanks for all the pros and cons. Bill
Forum: Early V8 (1932-53) 08-21-2020, 11:03 PM
Replies: 20
Views: 974
Posted By mhaim
Re: Which is easier

Rear end it is. Thanks for the help. Bill
Forum: Early V8 (1932-53) 08-21-2020, 01:30 PM
Replies: 20
Views: 974
Posted By mhaim
Which is easier

Want to replace the transmission in my 34 with a 39 unit I have. Which is easier. Pull the engine or the rear end. Thanks. Bill
Forum: Early V8 (1932-53) 06-03-2020, 04:37 PM
Replies: 10
Views: 655
Posted By mhaim
Re: 34 Stop light switch

Hope this works
Forum: Early V8 (1932-53) 04-25-2020, 12:35 PM
Replies: 21
Views: 1,136
Posted By mhaim
Re: Columbia tube routing beneath hood '36 Ford

I have a 34 but I used the 35-36 brackets to mount the plumbing.
Forum: Early V8 (1932-53) 02-22-2020, 11:38 PM
Replies: 13
Views: 725
Posted By mhaim
Forum: Early V8 (1932-53) 03-31-2019, 10:22 PM
Replies: 39
Views: 3,421
Posted By mhaim
Re: Lots of great 34 Ford footage! Netflix Highwaymen

Back in the early 30’s a new Thompson cost $225.00. that’s just over 11 $20 gold coins. 11 ounces of gold today is $1300 which is about $14500.00. That’s a lot of money for the cops to pay for one...
Forum: Early V8 (1932-53) 09-25-2017, 09:54 PM
Replies: 8
Views: 1,114
Posted By mhaim
Re: Ih 200 Napa condenser installation, 1935

And still another way to convert. Also get a good quality resister. My repro was junk.
Forum: Early V8 (1932-53) 12-05-2016, 11:50 PM
Replies: 34
Views: 5,239
Posted By mhaim
Re: 1934 Car Wooden Toeboard

12 1/2 on the inside and about 11 11/16 on underside. 45 degree angle on bottom.
Forum: Early V8 (1932-53) 11-14-2016, 11:28 PM
Replies: 4
Views: 920
Posted By mhaim
Re: air cleaner for a 94 carb

I used K&N E-3330. Has lots of surface and doesn't look to bad. Had to make a special screw for extra height.
Forum: Early V8 (1932-53) 09-13-2016, 08:43 PM
Replies: 260
Views: 36,868
Posted By mhaim
Re: Awwe Crap!

This is on eBay right now. Search his listing heading. Been for sale for quite a while. His shipping is worst than Mac's.
Forum: Early V8 (1932-53) 09-07-2016, 04:40 PM
Replies: 5
Views: 773
Posted By mhaim
Re: 1934 Accelerator Spring

I also got one from Mac's and ended up throwing it in the trash. The one that did work was bought on eBay from a parts supplier 1935fordtn. Put his name in search and see what he has.
Forum: Early V8 (1932-53) 08-24-2016, 09:19 PM
Replies: 6
Views: 1,183
Posted By mhaim
Re: 33,34,and 35 Spare Tire Cover Dimensions and related Tire Sizes

The 33,34,and35 face plates have stainless trim rings. The first one I found for my car was 27 3/4 X15 7/8 and it just didn't seem large enough in diameter to work. Then I found one 28 3/16 X 15 and...
Forum: Early V8 (1932-53) 07-15-2016, 08:51 PM
Replies: 8
Views: 952
Posted By mhaim
Re: Thumb screw ID

This is a 34 phaeton
Forum: Early V8 (1932-53) 01-05-2016, 06:31 PM
Replies: 1
Views: 584
Posted By mhaim
33-34 spare tire cover OD-ID

What is the inside and outside diameter of the 33-34 cover disc. I picked up one with a screwed on stainless ring and at 27 3/4 X 15 7/8 it's just a little small to catch the band all the way around....
Forum: Early V8 (1932-53) 11-22-2015, 04:12 PM
Replies: 6
Views: 1,762
Posted By mhaim
Re: V8 engine found half buried

Could the BBP8 actually be BB18
Forum: Early V8 (1932-53) 11-20-2015, 11:24 AM
Replies: 7
Views: 737
Posted By mhaim
Re: 34 Radiator Petcock-Where is it?

If you have the correct engine, ith peacocks are on the block just behind the front motor mount.
Forum: Early V8 (1932-53) 10-19-2015, 11:57 AM
Replies: 7
Views: 773
Posted By mhaim
Forum: Early V8 (1932-53) 01-28-2015, 03:37 PM
Replies: 13
Views: 1,801
Posted By mhaim
Re: 1933 Sedan rear shock "arms"

I took a pair of straight arms about ahe right length (maybe Model A) and used o torch to bend the dog leg in them. Worked out well. Bill
Forum: Early V8 04-15-2014, 02:41 PM
Replies: 2
Views: 754
Posted By mhaim
Re: 34 ring and pinion 4.11

Got a set of gears. Thanks for your help. Bill
Forum: Early V8 04-13-2014, 07:36 AM
Replies: 2
Views: 754
Posted By mhaim
Forum: Early V8 04-10-2014, 09:34 AM
Replies: 2
Views: 754
Posted By mhaim
34 ring and pinion 4.11

Wanted good used 4.11 gears for 34 Ford
781-738-2723
Showing results 1 to 22 of 22

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:36 AM.