Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 28
Search took 0.00 seconds.
Search: Posts Made By: Reddy
Forum: Model A (1928-31) 07-04-2015, 02:52 PM
Replies: 3
Views: 1,071
Posted By Reddy
Re: Red's Headers

Red's are tube type headers and I'm installing it on A block
Mike
Forum: Model A (1928-31) 07-04-2015, 01:47 PM
Replies: 3
Views: 1,071
Posted By Reddy
Red's Headers

I'm installing a set of Red's Headers what do I TORQUE them too ?
Thank you Mike
Forum: Model A (1928-31) 04-14-2015, 06:36 PM
Replies: 1
Views: 675
Posted By Reddy
Fender well cover

I'm looking to to see if anyone makes a patch to cover the wheel wells on a 1930-31 front fenders??
Thank you Mike
Forum: Model A (1928-31) 03-19-2014, 06:44 PM
Replies: 7
Views: 2,647
Posted By Reddy
Kiwi model A quick change

Has anyone on here builded a Kiwi Quickchange? I looking for pictures of the pinion being installed and what was used to to set the bearing and pinion in the housing.
Thank you Mike
Forum: Model A (1928-31) 12-13-2013, 07:41 PM
Replies: 7
Views: 1,135
Posted By Reddy
Re: inner axle shaft seals ??

Thanks to all,
I was thinking the inner seal was to be installed by the inner bearing race, but I see it is installed in the inside the axle housing on the outer side of the housing.
Mike
Forum: Model A (1928-31) 12-13-2013, 06:49 PM
Replies: 7
Views: 1,135
Posted By Reddy
Re: inner axle shaft seals ??

Tiny
Think you I'm sure I'll need the luck.
Mike
Forum: Model A (1928-31) 12-13-2013, 03:08 PM
Replies: 7
Views: 1,135
Posted By Reddy
inner axle shaft seals ??

Help,
I'm going to rebuild my model a rearend and I'm getting the bearing and all for the job. But I can find how the seal will mount on the inner axles or the bells ?
Is it installed before the...
Forum: Model A (1928-31) 06-18-2013, 08:38 AM
Replies: 14
Views: 1,634
Posted By Reddy
Re: Knocking

I did just install super winfield head and cam, at the same time I did the distributor.
So maybe the gas is to low in octane. Thank you all, I be working on this today and hope the timing and gas...
Forum: Model A (1928-31) 06-17-2013, 09:41 PM
Replies: 14
Views: 1,634
Posted By Reddy
Re: Knocking

It is more clatter than thud knock, and it more when it's under load of on a up climb
Mike
Forum: Model A (1928-31) 06-17-2013, 06:37 PM
Replies: 14
Views: 1,634
Posted By Reddy
Re: Knocking

I did about a year or so, not a lot of miles since I did
Mike
Forum: Model A (1928-31) 06-17-2013, 05:56 PM
Replies: 14
Views: 1,634
Posted By Reddy
Re: Knocking

I'm running Mallory single point distributors.
Mike
Forum: Model A (1928-31) 06-17-2013, 05:44 PM
Replies: 14
Views: 1,634
Posted By Reddy
Knocking

Hi,
I need some in site on this. My banger sound really good sitting as I speeding up the engine, but if I take it out for a ride it sound good and run strong. But as I running along and I speed it...
Forum: Model A (1928-31) 05-14-2013, 10:35 AM
Replies: 2
Views: 862
Posted By Reddy
manifold gaskets

Help,
Do you guys use sealing on you intake & exhaust manifold, if so what do you use ??
Thank you Mike
Forum: Model A (1928-31) 11-26-2012, 04:23 PM
Replies: 9
Views: 1,695
Posted By Reddy
Compression

What is the cylinder compression for a stock model A engine ????

Mike
Forum: Model A (1928-31) 05-05-2012, 12:39 PM
Replies: 2
Views: 937
Posted By Reddy
Re: F.A.S.T. Time Trial Event 7-7-12

Sorry Jim, That's Jack's car from S.L.O.
Mike
Forum: Model A (1928-31) 04-29-2012, 05:25 PM
Replies: 2
Views: 937
Posted By Reddy
F.A.S.T. Time Trial Event 7-7-12

The Guys of Central Coast (California) would like to invite you out to the F.A.S.T.
Time Trials event held in Santa Margarita on July 7th, 2012.
So tune up your old ride and come on out!
(See...
Forum: Model A (1928-31) 03-31-2012, 10:50 AM
Replies: 4
Views: 797
Posted By Reddy
Re: New cam

Thank you guys I plan to change oil pump and lifers at the same time.
Mike
Forum: Model A (1928-31) 03-31-2012, 10:31 AM
Replies: 4
Views: 797
Posted By Reddy
New cam

Can a cam be installed with the engine still in the car?
Mike
Forum: Model A (1928-31) 02-23-2012, 12:56 PM
Replies: 1
Views: 655
Posted By Reddy
Oil Pump

Hi,
Who makes and sells a higher out put Oil pump for model A engine?
Mike
Forum: Model A (1928-31) 10-25-2011, 03:30 PM
Replies: 8
Views: 1,632
Posted By Reddy
Re: Pitman arm

Kahuna,
Thank you Mike
Forum: Model A (1928-31) 10-25-2011, 03:00 PM
Replies: 8
Views: 1,632
Posted By Reddy
Pitman arm

Help,
Installed a shorted pitman arm on my 1930 pickup which already had a dropped
axle. The pitman arm was install with the ball facing out, have seen picture of the pitman ball facing the frame,...
Forum: Model A (1928-31) 10-01-2011, 06:47 PM
Replies: 5
Views: 1,274
Posted By Reddy
Re: Light switch rod

Thank you, jw
Mike
Forum: Model A (1928-31) 09-30-2011, 06:03 PM
Replies: 5
Views: 1,274
Posted By Reddy
Re: Light switch rod

Steve
Not sure as it's installed in the pickup and would have to remove the steering column from pickup to pull it out to check the length. But I'm sure I have to remove in time to make right.
Mike
Forum: Model A (1928-31) 09-30-2011, 05:05 PM
Replies: 5
Views: 1,274
Posted By Reddy
Light switch rod

Hi,
Installed a f-100 modified steering box for the model A's, in my 1930 model Pickup, and need to know how much of the light switch rod (by inches) sticks out the end. As the rod I have is to...
Forum: Model-A 06-09-2011, 01:59 PM
Replies: 0
Views: 451
Posted By Reddy
Model A rear end

Want, a Model A rear end, I am in the central coast of Ca. area.
Mike
Showing results 1 to 25 of 28

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:14 PM.