Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 19 of 19
Search took 0.00 seconds.
Search: Posts Made By: jughead
Forum: Early V8 (1932-53) 11-19-2014, 10:15 AM
Replies: 2
Views: 1,192
Posted By jughead
32 Cabriolet Windshield

Is the 32 Cabriolet windshield angle the same as a closed car? I've seen wiper motors noted for closed cars or open. Seems like the Cabriolet would be considered a closed car for this application....
Forum: Early V8 (1932-53) 09-14-2014, 04:39 PM
Replies: 4
Views: 1,226
Posted By jughead
Re: Stubborn Distributor Cap

My thanks to all responders. Light tapping from the opposite side popped it loose and away we go. Simple enough, but invaluable to the old newbie.

Thanks again
Forum: Early V8 (1932-53) 09-13-2014, 03:46 PM
Replies: 4
Views: 1,226
Posted By jughead
Stubborn Distributor Cap

I'm changing plug wires in my 32 V-8. The right side went fairly easy. But the left (driver side) not so. I can't seem to remove the distributor cap at all. After I release the wire bale, the cap is...
Forum: Early V8 08-19-2014, 03:41 PM
Replies: 0
Views: 617
Posted By jughead
32 Pitman Arm

Looking for a correct 32 Pitman Arm - Thanks
Forum: Early V8 (1932-53) 08-17-2014, 10:49 AM
Replies: 5
Views: 1,275
Posted By jughead
Re: 32 Pitman Arm Travel

Andy - Thanks for the comeback. I'm guessing parts are correct. The steering box to frame bolts are 3/8-24 x 1" with castle nuts & cotter pins on the outer side of the frame. The 1 7/16 nut uses a...
Forum: Early V8 (1932-53) 08-17-2014, 08:49 AM
Replies: 5
Views: 1,275
Posted By jughead
32 Pitman Arm Travel

Hi Guys - While trying to center my front wheels/steering wheel, I notice that the Pitman Arm bumps up against the bolt/nut used to attach the steering box to the frame. It contacts at both full...
Forum: Early V8 (1932-53) 06-03-2014, 03:09 PM
Replies: 2
Views: 1,273
Posted By jughead
32 Captured Nuts?

When I took my 32 horn bracket off, I believe a 3/8" nut fell of the bolt and down into never-never land. It looks like you need to remove the radiator splash shield to open up access to that area of...
Forum: Early V8 04-07-2014, 05:02 PM
Replies: 0
Views: 644
Posted By jughead
1932 Front Brake Drums

Hi Guys - I'm in need of one or two 32 front brake drums. Appreciate any leads. Thanks ([email protected])

Found two drums locally. Thanks to all who responded!
Forum: Early V8 (1932-53) 03-25-2014, 09:27 AM
Replies: 10
Views: 2,035
Posted By jughead
Charlotte Auto Fair

Anyone setting up at Charlotte? Would appreciate any spot locations that I could concentrate on. Charlotte is so big that the knees don't work very well after so many dead end searches. Thanks guys!
Forum: Early V8 (1932-53) 03-06-2014, 10:36 AM
Replies: 86
Views: 14,849
Posted By jughead
Re: Does lack of an 800 Telephone number deter ordering from parts houses?

I have no long distance carrier on my land line and rely on a prepaid cell phone when 800 numbers are not available. But cell phone service in my area is marginal at best, sometimes forcing me to...
Forum: Early V8 (1932-53) 02-28-2014, 10:15 AM
Replies: 16
Views: 2,530
Posted By jughead
Re: seat identification...1932??

David - Thanks much for the response. I wonder if what I have might not be a 32 seat due to the absence of the wood bottom frame. The current seat bottom does not slide all the way back under the...
Forum: Early V8 (1932-53) 02-19-2014, 05:08 PM
Replies: 16
Views: 2,530
Posted By jughead
Re: seat identification...1932??

Hi David - I'm in the early stages of trying define just what I have in my 32 Cabriolet, currently focusing on the seat. The seat bottom does not have the wood base shown in the picture on page 15-2....
Forum: Early V8 (1932-53) 02-03-2014, 03:32 PM
Replies: 6
Views: 1,792
Posted By jughead
32 Throttle Rod Connection to Gas Pedal

Hi - It appears that my throttle rod attaches to a bell crank on the inside of my Cabriolet firewall. From there, a shorter rod goes from that bell crank down to the gas pedal. I haven't seen any...
Forum: Early V8 (1932-53) 01-26-2014, 04:39 PM
Replies: 1
Views: 828
Posted By jughead
32 Floorboard Screw Size

Might anyone remember the size of the floorboard screws on the 1932? It looks like maybe 12-xx? I don't want to mess things up when I chase the threads. Thanks much.

Dick
Forum: Early V8 (1932-53) 12-05-2013, 05:43 PM
Replies: 0
Views: 927
Posted By jughead
32 Rear Hood Bracket Fit

Has anyone run into problems with how the rear hood bracket fits to the cowl/firewall area? My repop bracket fits good on the cowl side but the two other holes on the front firewall side don't line...
Forum: Early V8 (1932-53) 11-29-2013, 04:47 PM
Replies: 32
Views: 5,645
Posted By jughead
Re: 1932 roadster - no S/N

Hi - Trying to correlate serial numbers on a roadster that has the body on. I realize the need to pull the body to see two of the numbers on the frame rail. What's involved with searching for the...
Forum: Early V8 (1932-53) 11-23-2013, 10:24 AM
Replies: 4
Views: 1,338
Posted By jughead
Re: Antifreeze for my 32

Thanks guys. I have the distilled water ready to go after I flush out the system. I'm trying to finish up and evaluate a previously started restoration of my 32 Cabriolet V8, so I'm sure there will...
Forum: Early V8 (1932-53) 11-22-2013, 05:10 PM
Replies: 4
Views: 1,338
Posted By jughead
Antifreeze for my 32

Anybody have a suggested Brand Name for antifreeze for my 32? Thanks - Jughead
Forum: Early V8 10-29-2013, 10:04 AM
Replies: 59
Views: 11,208
Posted By jughead
Showing results 1 to 19 of 19

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:34 AM.