Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Bob Bidonde
Forum: Model A (1928-31) 12-05-2019, 09:05 AM
Replies: 15
Views: 714
Posted By Bob Bidonde
Re: High compression head vs cooling

In my experience, the engines run cooler due to more efficient power stroke combustion.
Forum: Model A (1928-31) 12-02-2019, 09:02 AM
Replies: 7
Views: 457
Posted By Bob Bidonde
Re: Wishbone/Trans Connection

Rubber wears rapidly, so it is less durable than the steel parts of the original radius rod ball joint. Given that the radius rod ball is worn, you have choices to restore the joint:
1. Replace the...
Forum: Model A (1928-31) 12-02-2019, 08:33 AM
Replies: 22
Views: 863
Posted By Bob Bidonde
Re: Do You Guys Constantly Re-touch Wheel Spokes?

Painted wheels need touch ups often, but powder coated wheels do not.
Forum: Model A (1928-31) 12-01-2019, 12:09 PM
Replies: 3
Views: 214
Posted By Bob Bidonde
Re: B headgasket

The gaskets are the same except for 2 coolant holes that are in the Model B gasket. The Model A gasket is on the left. You can use the Model B gasket in both the Model A and Model B engines.
Forum: Model A (1928-31) 11-27-2019, 08:36 AM
Replies: 41
Views: 942
Posted By Bob Bidonde
Re: 12 volt coil with resistor

In 12V electrical systems with breaker point ignitions, ignition coils start the vehicle on 12V through the coil, and the resistor drops the coil to 6V to 8V once the engine is running.
Forum: Model A (1928-31) 11-26-2019, 12:33 PM
Replies: 8
Views: 509
Posted By Bob Bidonde
Re: Double Venturi Carb using?

The Ford Service Bulletins, Pages 206, 207, 208 & 209 give an excellent description and operation of the Zenith Double Venturi carburetor.

The Secondary Venturi (#10) increases the inlet air...
Forum: Model A (1928-31) 11-21-2019, 11:57 AM
Replies: 7
Views: 324
Posted By Bob Bidonde
Re: 1931 Slant Window Cabriolet outside mirrors

You need reproduction accessory mirrors like these that are on my Victoria.
Forum: Model A (1928-31) 11-21-2019, 11:53 AM
Replies: 14
Views: 744
Posted By Bob Bidonde
Re: #1 plug question

You need to be concerned with the hi-voltage components of the distributor that are the body and the rotor. Modify a distributor cap so you can see what is going on as the rotor passes the #1 contact...
Forum: Model A (1928-31) 11-20-2019, 12:44 PM
Replies: 10
Views: 690
Posted By Bob Bidonde
Re: Proper crankshaft grinding

Check this article

Watch this Model "A" crankshaft being ground...
Forum: Model A (1928-31) 11-18-2019, 11:10 AM
Replies: 2
Views: 256
Posted By Bob Bidonde
Re: Rubber pads for tail lamp and head lamp stands.

I use one layer of clear shipping tape cut to the shape of the foot print to protect the paint. Works well and cannot be seen. It is also very inexpensive.
Forum: Model A (1928-31) 11-17-2019, 09:54 AM
Replies: 13
Views: 645
Posted By Bob Bidonde
Re: Data plate rivet holes don't line up

I had this problem when restoring my 190A. Rather than rework the original holes in the firewall, I pulled the holes in data plate using a rat tail file. Look closely and you can see the elongation...
Forum: Model A (1928-31) 11-17-2019, 09:05 AM
Replies: 6
Views: 387
Posted By Bob Bidonde
Re: Oil pressure . . . normal?

The valve chamber is vented to the atmosphere via the crankcase, so once pumped oil reaches the end of the tube in valve chamber, its gauge pressure is zero.

Oil pressure between the oil pump...
Forum: Model A (1928-31) 11-17-2019, 08:50 AM
Replies: 5
Views: 315
Posted By Bob Bidonde
Re: Oil Pump Question

Hi Tom,

Thanks for posting the oil pan tray info.
Forum: Model A (1928-31) 11-17-2019, 08:43 AM
Replies: 23
Views: 970
Posted By Bob Bidonde
Re: B model distributor question

I do not believe this to be a 1932-1934 Ford distributor.
Forum: Model A (1928-31) 11-16-2019, 11:25 AM
Replies: 2
Views: 231
Posted By Bob Bidonde
Re: Bendix Spring bolts

The Bendix starter drives were troublesome throughout the Model "A" years judging by the quantity of service bulletins issued about them. My comments regard the A-11350-C Drive.

Refer to the Ford...
Forum: Model A (1928-31) 11-16-2019, 11:03 AM
Replies: 7
Views: 443
Posted By Bob Bidonde
Re: Window Riser Handles - Original or Repro?

Most originals are die cast and nickle plated.
Forum: Model A (1928-31) 11-16-2019, 08:26 AM
Replies: 23
Views: 970
Posted By Bob Bidonde
Re: B model distributor question

The distributor lock bolt is the same 1928 - 1934.
Forum: Model A (1928-31) 11-15-2019, 12:19 PM
Replies: 32
Views: 1,685
Posted By Bob Bidonde
Re: Removed engine; some improvements?

Replace & rebuild:

Clutch Disc
Pressure Plate
Throw-Out Bearing
Transmission Pilot Bearing in Flywheel
Front Engine Mount Springs
Rubber Pads on Rear Engine Mounts
All Engine Gaskets...
Forum: Model A (1928-31) 11-15-2019, 11:39 AM
Replies: 73
Views: 12,242
Posted By Bob Bidonde
Re: How Many Model A's are left ?

The survival number of Model "A" Fords is unrivaled by any other make and model of automobile.
Forum: Model A (1928-31) 11-13-2019, 02:32 PM
Replies: 13
Views: 849
Posted By Bob Bidonde
Re: Modern Shocks any good?

Before giving up on your shocks, try changing the tire pressure. let the tire sidewalls do some of ride damping. Try 32, 30, & 28 psig.
Forum: Model A (1928-31) 11-11-2019, 08:24 AM
Replies: 51
Views: 1,720
Posted By Bob Bidonde
Forum: Model A (1928-31) 11-11-2019, 08:16 AM
Replies: 37
Views: 2,171
Posted By Bob Bidonde
Re: MMO non believers

I can understand the shutoff valve and carburetor getting deposits from modern gasoline if it is allowed to evaporate in the system. However, every time I put my Model A's away for the day, I run my...
Forum: Model A (1928-31) 11-11-2019, 07:59 AM
Replies: 25
Views: 902
Posted By Bob Bidonde
Re: Cold Weather Operation

I have driven my Coupe in below zero weather. The only difficulty was shifting the transmission until the gear oil warmed-up. The speedometer also was erratic because some grease was in the cable.
Forum: Model A (1928-31) 11-08-2019, 08:01 AM
Replies: 7
Views: 462
Posted By Bob Bidonde
Re: Spring Prep

Solvent clean, spray with gloss black paint and install spring covers wet with 140 gear oil.
Forum: Model A (1928-31) 11-08-2019, 07:58 AM
Replies: 9
Views: 995
Posted By Bob Bidonde
Re: Black fender paint

I choose DuPont's Nason single stage urethane for its durability, ease of touch-up and comparable lower cost. Gloss without color sanding is excellent. Very little orange peel.
Showing results 1 to 25 of 500

Forum Jump
Sponsored Links (Register now to hide all advertisements)

All times are GMT -5. The time now is 07:06 PM.