Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 18 of 18
Search took 0.00 seconds.
Search: Posts Made By: V8Vic
Forum: Early V8 (1932-53) 11-29-2022, 02:52 PM
Replies: 3
Views: 1,029
Posted By V8Vic
Re: 32 short rear bumper brackets

I bought a pair from him a couple of years ago. They fit fine and look great on my '32 tudor. "Dont have a phone but his e-mail was [email protected] Hope this helps, Vic
Forum: Early V8 (1932-53) 11-02-2022, 02:03 PM
Replies: 10
Views: 1,222
Posted By V8Vic
Re: Ford Wire Wheels

Back in the late '80s, Rex Gardner and I had some problems with Kelsey and Ford wire wheels on our Great Race '35 coupe. Apparently, the wheels were just moving around enough to shred our new Coker...
Forum: Early V8 02-27-2021, 11:00 AM
Replies: 3
Views: 1,361
Posted By V8Vic
Re: '36 Engine

Sold, Please remove
Forum: Early V8 02-20-2021, 12:17 PM
Replies: 3
Views: 1,361
Posted By V8Vic
Re: '36 Engine

Drop Price..…..now $975
Forum: Early V8 (1932-53) 01-14-2021, 11:09 AM
Replies: 33
Views: 6,723
Posted By V8Vic
Re: who best to drop 1932 ford axle

Joe Casto south of Ponca City OK does a great job. He's done several for me and also does the spindles if you need. Joes Speed Shop 580-268-3704
Forum: Early V8 12-04-2020, 03:53 PM
Replies: 3
Views: 1,361
Posted By V8Vic
Re: '36 Engine

Bttt … Offers?
Forum: Early V8 11-27-2020, 01:26 PM
Replies: 3
Views: 1,361
Posted By V8Vic
'36 Engine

'36 LB Engine, has about 25K miles, complete from pan to intake, will need water pumps, starter, ignition and exhaust manifolds. Was used in TSD Rally car, bored .030, Isky lifters, mild Crane cam....
Forum: Early V8 (1932-53) 07-10-2019, 04:50 PM
Replies: 26
Views: 8,053
Posted By V8Vic
Re: Colorado Flathead Rebuilder

Try Gene French in Nunn CO (970)581-2808

I have spent about 30K miles in a '36 Coupe powered by a '36LB he rebuilt
Forum: Early V8 (1932-53) 02-06-2019, 12:30 PM
Replies: 8
Views: 1,327
Posted By V8Vic
Re: 34 Coupe fuel pickup question

Elwood, got a question about tank replacing, on a '34 Coupe, is it required to raise the body or just that "pan" above the tank when replacing ? This is for a pal, I'm a '32 guy myself. Vic
Forum: Early V8 09-26-2015, 08:47 AM
Replies: 4
Views: 1,863
Posted By V8Vic
Forum: Early V8 09-21-2015, 02:03 PM
Replies: 4
Views: 1,863
Posted By V8Vic
Forum: Early V8 09-13-2015, 11:18 AM
Replies: 4
Views: 1,863
Posted By V8Vic
Forum: Early V8 09-09-2015, 10:56 AM
Replies: 4
Views: 1,863
Posted By V8Vic
Forum: Early V8 09-05-2015, 02:00 PM
Replies: 4
Views: 1,863
Posted By V8Vic
'32 Ford Frame

JW Rod Shop '32 rails with bolted in Gennie '32 crossmembers (cleaned and primed) $2000, you pick up. also have JW boxing plates if you need them. Great start for Resto or Rod... rear X-membr trimmed...
Forum: Early V8 (1932-53) 07-24-2014, 04:05 PM
Replies: 29
Views: 7,161
Posted By V8Vic
Re: Merc crank in 36LB block

ROTERWRENCH, sorry it took me so long to get back to you. Rex is the owner, driver and mechanic , I'm just the "gofer" and the navigator on this project. Briefly, he uses 3/16" sleeves, the bore...
Forum: Early V8 (1932-53) 07-06-2014, 08:03 PM
Replies: 29
Views: 7,161
Posted By V8Vic
Re: Merc crank in 36LB block

918 786 1950 Shop Phone 918 801 2406 cell
Forum: Early V8 (1932-53) 07-06-2014, 12:05 PM
Replies: 29
Views: 7,161
Posted By V8Vic
Re: Merc crank in 36LB block

I'm one of those "Blokes", navigated that red '35 Coupe for a number of years in the GAR, the 21 stud Merc always ran great..problems always were with something else. Rex is still building these...
Forum: Early V8 07-31-2011, 03:22 PM
Replies: 6
Views: 1,414
Posted By V8Vic
Re: Rear radius rods

I have a real nice pair, no pitting, etc. $150 plus shipping from 67068
E-mail me and I'll send pictures. V8Vic [email protected]
Showing results 1 to 18 of 18

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:19 AM.