Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 18 of 18
Search took 0.01 seconds. Search: Posts Made By: Jet96
Forum: Model A (1928-31) 11-12-2022, 03:42 PM
Replies: 17
Views: 1,859
Posted By Jet96
Re: Chunks in the oil pan

Yes sir you get double your pleasure with one of Murray's dampers. I really like mine and it fit perfectly.
Forum: Model A (1928-31) 11-07-2022, 07:31 AM
Replies: 37
Views: 5,881
Posted By Jet96
Re: Starter Drive Bendix Spring Question

I'm glad you got it sorted. Batteries are kind of a crap shoot anymore. Some don't last at all and then the next one will work flawlessly for 8 or 9 years...
Forum: Model A (1928-31) 11-07-2022, 06:49 AM
Replies: 32
Views: 5,396
Posted By Jet96
Re: 28 A, Bad shake... guidance please...

On my ccpu it ended up being the ball on the pitman arm was worn nearly flat. It would drive fine and then if you hit a bump it would start shaking its head.
Forum: Early V8 (1932-53) 11-07-2022, 12:09 AM
Replies: 18
Views: 2,712
Posted By Jet96
Re: A Cheating Intake

That's pretty cool!
Forum: Early V8 (1932-53) 11-07-2022, 12:06 AM
Replies: 27
Views: 4,432
Posted By Jet96
Re: Holley 94 rebuild

I agree- 97's and 94's are pretty easy to rebuid. The videos are pretty clear and helpful. He has a few little tricks from many years of mesding with them.
Forum: Early V8 (1932-53) 11-06-2022, 11:34 PM
Replies: 41
Views: 5,328
Posted By Jet96
Re: 1937 Flathead Won't Run Well

In regards to the power valve, they can look perfect and still seep. I finally filled them with gas and let them sit on a couple bolts and you could see it well up around the pv. I took mine to a...
Forum: Early V8 (1932-53) 11-06-2022, 10:58 PM
Replies: 7
Views: 768
Posted By Jet96
Re: Helmet distributor side caps

This is timely as I'm going to go over a 37 engine/trans this winter.
Forum: Early V8 (1932-53) 11-06-2022, 10:38 PM
Replies: 3
Views: 572
Posted By Jet96
Re: Big Inch Flatty: Crank endfloat fix. Part 2. Setting the endfloat.

I always enjoy you working through issues as they pop up. Thanks for the videos.
Forum: Early V8 (1932-53) 11-06-2022, 10:26 PM
Replies: 17
Views: 1,096
Posted By Jet96
Re: 1937 Transmission Synchronizers

I'm glad I read this. I'm looking at going into my 37 trans this winter and thought it was same as the 39.
Forum: Early V8 (1932-53) 11-06-2022, 10:22 PM
Replies: 58
Views: 13,158
Posted By Jet96
Re: Columbia vs Mitchell overdrive

That article is quite helpful.
Forum: Early V8 (1932-53) 11-06-2022, 10:15 PM
Replies: 24
Views: 1,947
Posted By Jet96
Re: Crankcase ventilation on a supercharged engine

That's an interestig setup- I may need to look into one. Thanks for the info.
Forum: Early V8 (1932-53) 11-06-2022, 10:09 PM
Replies: 25
Views: 2,953
Posted By Jet96
Re: 42- 48 Ford crab

Tippo -that's a good idea to install the spring type coil, thanks.
Forum: Early V8 (1932-53) 11-06-2022, 10:05 PM
Replies: 10
Views: 1,004
Posted By Jet96
Re: clutch question

Yes you can rotate the shaft. It's pretty stiff but a 18" crescent worked fine.
Forum: Early V8 (1932-53) 11-06-2022, 10:02 PM
Replies: 13
Views: 2,110
Posted By Jet96
Re: steering box

That's a good tip on the screw length.
Forum: Early V8 (1932-53) 11-06-2022, 09:47 PM
Replies: 24
Views: 2,371
Posted By Jet96
Re: 1934 Ford 1 1/2 ton Truck Awaken after 70 years

Wow only 18k -What a find!
Forum: Model-A 08-20-2019, 04:07 AM
Replies: 0
Views: 1,132
Posted By Jet96
Mitchell O/D

Sold
Forum: Early V8 (1932-53) 03-22-2015, 12:53 PM
Replies: 13
Views: 2,355
Posted By Jet96
Re: Engine id.

Raised intake deck pretty much narrows it down...
Forum: Early V8 (1932-53) 03-18-2015, 12:27 PM
Replies: 19
Views: 3,816
Posted By Jet96
Re: Water Pumps

Dang, that thing sounds like it's been eatin' its spinach for sure! Nice sounding flattie!
Showing results 1 to 18 of 18

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:17 PM.