Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 112
Search took 0.01 seconds.
Search: Posts Made By: dennis lumbert
Forum: Model A (1928-31) 08-18-2020, 11:10 AM
Replies: 10
Views: 663
Posted By dennis lumbert
90th birthday celebration

Hi all, I was Blessed to celebrate my moms 90th birthday yesterday.My Tudor is the same age so they shared the spotlight .I thought Id share a few pics with you.Hope you enjoy them. Best...
Forum: Model A (1928-31) 08-12-2020, 01:25 PM
Replies: 14
Views: 584
Posted By dennis lumbert
Re: Clutch pressure plate New or Reconditioned?

I have a new one that I installed with my AER rebuilt engine 2100 miles ago . It has functions perfectly so far .I used a new disc from Berts and adjusted the pressure plate fingers at install.
Forum: Model A (1928-31) 07-13-2020, 01:06 PM
Replies: 8
Views: 604
Posted By dennis lumbert
Re: Fender welting

There is no welting between the fender and the running board.I used a piece of cloth friction tape ,it’s not noticeable .
Forum: Model A (1928-31) 05-26-2020, 09:30 AM
Replies: 4
Views: 497
Posted By dennis lumbert
Re: Tudor seat pic request

Heres my 30 STD Tudor.
Forum: Model A (1928-31) 05-24-2020, 12:53 PM
Replies: 5
Views: 607
Posted By dennis lumbert
Re: 1930 Tudor visor

Mine was spot welded just like you described.
Forum: Model A (1928-31) 05-21-2020, 11:06 AM
Replies: 18
Views: 1,643
Posted By dennis lumbert
Re: Lower cylinder head

I used a copper gasket on the goose neck when assembling my engine 8 years ago.The next day I was in my shop and heard a loud bang noise over by engine .Went over to see what it was and found the...
Forum: Model A (1928-31) 05-03-2020, 07:55 PM
Replies: 8
Views: 1,262
Posted By dennis lumbert
Re: B heads starting to...

Very,very nice!!!
Forum: Model A (1928-31) 04-17-2020, 09:20 PM
Replies: 29
Views: 2,061
Posted By dennis lumbert
Forum: Model A (1928-31) 04-01-2020, 01:28 PM
Replies: 7
Views: 622
Posted By dennis lumbert
Re: Oil pump install question

The thread size for the hole is 1/8 “ pipe thread.
Forum: Model A (1928-31) 04-01-2020, 01:02 PM
Replies: 7
Views: 622
Posted By dennis lumbert
Re: Oil pump install question

The oil pump is held in place by the spring mounted to the bottom of the pump.No bolt,the hole is sealed with a pipe plug.Dont remember the pipe plug thread size.
Forum: Model A (1928-31) 03-31-2020, 04:49 PM
Replies: 8
Views: 462
Posted By dennis lumbert
Re: Horn Wires Polarity

No polarity does not matter on the horn.
Forum: Model A (1928-31) 03-22-2020, 03:29 PM
Replies: 12
Views: 937
Posted By dennis lumbert
Re: Two tooth stearing box

The eccentric adjusting sleeve it is used to adjust gear to gear play to zero at the exact center of the steering wheel full rotation(full rotation is 3 turns so center is 1 1/2 turns from either...
Forum: Model A (1928-31) 03-22-2020, 03:29 PM
Replies: 12
Views: 937
Posted By dennis lumbert
Re: Two tooth stearing box

The eccentric adjusting sleeve it is used to adjust gear to gear play to zero at the exact center of the steering wheel full rotation(full rotation is 3 turns so center is 1 1/2 turns from either...
Forum: Model A (1928-31) 01-29-2020, 09:00 PM
Replies: 7
Views: 700
Posted By dennis lumbert
Re: Shell Oil Canister

Well I didn’t read your post close enough the first time and thought it was a metal canister.Maybe it’s some sort of water injector to help remove carbo from the combustion chambers.Just a guess.
Forum: Model A (1928-31) 01-29-2020, 08:39 PM
Replies: 7
Views: 700
Posted By dennis lumbert
Re: Shell Oil Canister

I’m thinking someone used it for a vacuum storage tank for a vacuum wipe wipe motor.That would keep the wipers going when under heavy engine loads and the vacuum normally drops off.Dont need it in my...
Forum: Model A (1928-31) 01-29-2020, 08:24 PM
Replies: 3
Views: 523
Posted By dennis lumbert
Re: 30 model A panel

They take two rubber pieces ,one upper and one lower.Also a metal piece that goes in after the rubber is installed.They require patients to install. Dennis
Make sure all the old rubber has been...
Forum: Model A (1928-31) 01-18-2020, 10:42 PM
Replies: 28
Views: 2,630
Posted By dennis lumbert
Re: Engine pans

Kind of hard to take pictures of but I gave it my best attempt
Forum: Model A (1928-31) 01-18-2020, 02:13 PM
Replies: 9
Views: 911
Posted By dennis lumbert
Re: Voltage meter

You can buy a current probe that will measure current flow through a wire .It must be used in conjunction with a digital volt meter ,(dvm). It can be used to measure amps or milliamperes .You can...
Forum: Model A (1928-31) 12-22-2019, 12:45 PM
Replies: 11
Views: 1,244
Posted By dennis lumbert
Re: The Old Opportunity Motor

Thanks for taking the time to share this Russ /40. Dennis
Forum: Model A (1928-31) 12-11-2019, 09:35 AM
Replies: 25
Views: 2,641
Posted By dennis lumbert
Re: Babbit vs Inserts

There are many ,many members on this forum who have driven 10s of thousands of miles with inserted engines.Opinions will vary and lots of disscussions on this if you do a search.
...
Forum: Model A (1928-31) 12-09-2019, 09:00 PM
Replies: 8
Views: 893
Posted By dennis lumbert
Re: Side Mirrors

I had the same problem with my Tudor.I bought a 1/4 “ stainless bolt of the proper length at tractor supply,chucked the bolt in a electric drill and ground the head down on a bench grinder to resembe...
Forum: Model A (1928-31) 11-30-2019, 09:20 PM
Replies: 58
Views: 4,013
Posted By dennis lumbert
Re: Using Ford Barn as an distraction

I’m saddened to learn of your great loss.May God give you comfort and strength to get through this. Dennis Lumbert
Forum: Model A (1928-31) 11-22-2019, 11:49 AM
Replies: 9
Views: 702
Posted By dennis lumbert
Re: Normal Clutch Chatter

I have a new pressure plate that I adjusted as per service bulliten ,a new disc and resurfaced flywheel.1500 miles and has a always been smooth.I have original motor mounts,(30 Tudor).
Forum: Model A (1928-31) 11-18-2019, 08:54 PM
Replies: 18
Views: 1,970
Posted By dennis lumbert
Re: Post Model A Picture

Great looking car.
Forum: Model A (1928-31) 10-30-2019, 12:00 PM
Replies: 8
gas
Views: 849
Posted By dennis lumbert
Re: gas

POR 15 cleaner/degreaser,(formally called marine clean)
Showing results 1 to 25 of 112

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:34 PM.