Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: 160B
Forum: Model A (1928-31) 02-21-2019, 06:44 PM
Replies: 10
Views: 508
Posted By 160B
Re: Air Filter

K&N only way to go, I have the K&N E3050 on both my Model A's

The calculation on the below web site are at an engine running 2800 rpm, and the conclusion is you can use any one of three filters,...
Forum: Model A (1928-31) 02-19-2019, 03:57 PM
Replies: 12
Views: 582
Posted By 160B
Re: Canadian tool mark

Here are copies of RG&JS F-29 Revised 2016 and F30 Revised 2016 for Canadian vehicles area 17 Tools
Forum: Model A (1928-31) 02-18-2019, 07:30 PM
Replies: 8
Views: 458
Posted By 160B
Re: Rear Hub Grease Seal Removal Tool

Steve here are photos of a tool for split rims that I use to remove rear axle seals. I put the drum in a vice and pry the seal out.
Forum: Model A (1928-31) 02-13-2019, 02:44 PM
Replies: 20
Views: 659
Posted By 160B
Re: Reproduction rear spare tire bracket

RG&JS 22-13 Revised 2011 rear spare wheel carriers.

There are 18 different carriers
Forum: Model A (1928-31) 02-06-2019, 10:57 PM
Replies: 8
Views: 545
Posted By 160B
Re: Clutch travel

Yes, adjust the length of the clutch adjusting arm.


Adjusting the Clutch Pedal – The clutch pedal clearance can be adjusted by tightening or loosening the release arm rod. This is accomplished...
Forum: Model A (1928-31) 02-03-2019, 08:00 PM
Replies: 21
Views: 752
Posted By 160B
Re: Oil pan baffle

and do not have a oil/sludge mess that you can get by dropping
Forum: Model A (1928-31) 02-03-2019, 02:31 PM
Replies: 2
Views: 279
Posted By 160B
Almost Spring Swap Meet 2019 March 16 & 17

Almost Spring Swap Meet & Car Show (Puyallup WA) 2019 March 16 & 17

Washington State Fair Events Center
Gallopin Gertie Model A Ford Club 39th annual
110 9th Ave SW
Puyallup, WA 98371
Open...
Forum: Model A (1928-31) 02-02-2019, 11:49 PM
Replies: 7
Views: 577
Posted By 160B
Re: tires

I went through the process of getting new tubes in August of 2017 and ended up getting tubes from Bert’s Model A. Other vendors tubes had the valve stem off center and I did not want to use them.
...
Forum: Model A (1928-31) 01-26-2019, 11:50 PM
Replies: 51
Views: 2,022
Posted By 160B
Re: Insurance

Hagerty!!!
Forum: Model A (1928-31) 01-26-2019, 06:43 PM
Replies: 14
Views: 864
Posted By 160B
Re: Brake assembly, Roadster

In the attached photo note the position of the cotter pin on the Pin Emergency Brake Toggle Lever. The cotter pins need to be inboard so they do not rub against the brake drum. The return springs in...
Forum: Model A (1928-31) 01-26-2019, 06:22 PM
Replies: 14
Views: 864
Posted By 160B
Re: Brake assembly, Roadster

Werner

see post #15 on the below thread


https://www.fordbarn.com/forum/showthread.php?p=1720328#post1720328
Forum: Model A (1928-31) 01-26-2019, 06:18 PM
Replies: 17
Views: 644
Posted By 160B
Re: Emergency brake issues

see the attached pdf from the Bratton's catalog, note the position of the cotter pin, PC #17 on the Pin Emergency Brake Toggle Lever PC# 19. The cotter pins need to be inboard so they do not rub...
Forum: Model A (1928-31) 01-26-2019, 05:40 PM
Replies: 17
Views: 936
Posted By 160B
Re: Brake Pills

Concave Steel Cup that fits in the wedge to lengthen the brake actuating rod, see attached photo, not to scale.
Forum: Model A (1928-31) 01-25-2019, 10:31 AM
Replies: 3
Views: 250
Posted By 160B
Re: Speedometer ID

Use the attached RG&JS 6-3 Revised 2011 and you should be able to determine if the speedometer is Stewart Warner, North East or Waltham.
Forum: Model A (1928-31) 01-25-2019, 12:44 AM
Replies: 6
Views: 503
Posted By 160B
Re: Mafca nwrm 2019

Sent my registration in 1/13/2019 via email and the check was mailed on 1/12/2019!!!
Forum: Model A (1928-31) 01-23-2019, 07:51 PM
Replies: 15
Views: 713
Posted By 160B
Re: brake parts and grease

FWIW

I did not say anything about the springs, I noted that "The emergency brake toggle lever pins are not installed correctly, the pins are in backwards the cotter pin should be behind the lever....
Forum: Model A (1928-31) 01-23-2019, 07:43 PM
Replies: 15
Views: 713
Posted By 160B
Re: brake parts and grease

FWIW

The emergency brake toggle lever pins are not installed correctly, the pins are in backwards the cotter pin should be behind the lever. With the cotter pin outboard they will rub against the...
Forum: Model A (1928-31) 01-21-2019, 05:57 PM
Replies: 11
Views: 679
Posted By 160B
Re: Front brake floater, Roadster

The steel drum has a rolled edge at the outer diameter and the cast iron drum is solid at the outer diameter, see attached photo. Cast Iron drum on the left, steel drum on the right.
Forum: Model A (1928-31) 01-17-2019, 08:30 PM
Replies: 10
Views: 447
Posted By 160B
Re: Roadster Door Knob

RG&JS 12-10 Revised 2016 1928 Roadster, Phaeton (door handle lever arms nickel plated through 6/28 then painted black)


RG&JS Canadian F does not have any information on Area 12 Miscellaneous...
Forum: Model A (1928-31) 01-17-2019, 07:47 PM
Replies: 10
Views: 447
Posted By 160B
Re: Roadster Door Knob

FWIW

Looking at the RG&JS I would say the octagonal lever arm knob is correct. Look at the attached RG&JS 12-10 revised 2016 item "W".
Forum: Model A (1928-31) 01-11-2019, 11:25 PM
Replies: 32
Views: 1,923
Posted By 160B
Re: Check your fan blades

Here is a photo of the remains of a water pump that was destroyed when an original two bladed fan failed.
Forum: Model A (1928-31) 01-11-2019, 04:51 PM
Replies: 53
Views: 4,599
Posted By 160B
Re: LED Headlights

Where can you purchase them and what is the price?
Forum: Model A (1928-31) 01-11-2019, 01:30 PM
Replies: 3
Views: 513
Posted By 160B
Re: Handle Restoration

Here are the pages from The Restorer magazine November - December 1980
Forum: Model A (1928-31) 01-09-2019, 08:27 PM
Replies: 15
Views: 914
Posted By 160B
Re: brake linings

FWIW

There is hard bonded and soft bonded, the soft bond you can feel a slight depression with your thumb nail. Soft bonded will work with mechanical brakes and steel and cast iron drums.

Hard...
Forum: Model A (1928-31) 01-06-2019, 09:02 PM
Replies: 3
Views: 329
Posted By 160B
Re: intake color

Intake manifold finish should be Engine green. see attached RG&JS
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:25 PM.