Looking for some advice....
 

So I have my engine compartment looking really nice, the only area that looks a little off is the muffler clamp....see pic.

For some reason my father-in-law packed a bunch of sealer around the connection, not sure why. My question is am I going to open a can of worms if I remove the sealer and put on a new clamp.....right now it seems to be well sealed, it runs quiet with no leaks.

I'm probably better off just leaving it alone but thought I would ask.

Thanks

Nick

Re: Looking for some advice....
 

If you are happy with the "looks", then leave it...BUT if it were me, and a few others I might add, and you want it to look really, really nice, then I would just take some time and clean it up and get rid of those pesky "worms"!!! Remove the manifold to or just clean it up on the engine. I think you would be much more happy then.

Pluck

Re: Looking for some advice....
 

I personally would leave it... Although it is an eye sore, there's a reason behind most things.

Re: Looking for some advice....
 

Thanks guys...

Most of me goes along with what Steve said, I know I'd be much happier if it looked better.....that said part of me got along with what DJ said, I'm guessing my father-in-law put it there for a reason but n the other hand he often did things to be on the safe side.

If I do decide to mess with it, besides a new clamp, and it sounds like Snyder's has a good one, is there anything else I should buy.

Re: Looking for some advice....
 

Nope it is just the clamp, manifold and muffler. That is all that is there.

Mike

Re: Looking for some advice....
 

Thank you Mike

Re: Looking for some advice....
 

Well, it all depends and you won't know what you're dealing with until you pull it apart. For all you know, the flange on the muffler could be all mangled and you may need to rework the flange or need to purchase an entirely new muffler. For starters I would purchase a new muffler clamp from brattons, an exhaust sleeve, and new brass nuts and bolts.

Re: Looking for some advice....
 

Thank you DJ....

Re: Looking for some advice....
 

I would hold off buying parts until you see what you have.

Re: Looking for some advice....
 

That mess of worms maybe asbestes! I would remove it wet with water and outdoors!

Re: Looking for some advice....
 

^x2

Re: Looking for some advice....
 

I would cut it off- looks ugly as sin!

Re: Looking for some advice....
 

Ronn Ya think:eek:

My ass would be buying a new exhaust porcelain coated, and intake manifolds, copper manifold gasket, new studs and nuts / washers, pc'ed exhaust/ pipe clamp, insert pipe and a muffler assy if need be :):). But DAD sends me lots of $$ each month also:rolleyes:
SAsooonoout

Re: Looking for some advice....
 

If you feel it's an eye sore go for it... I happen loose a but on my clamp the other day and for about $20 (includes shipping) you can have it the way you want.. Besides, as I discovered on mine it was a leak point...

Re: Looking for some advice....
 

I use a coat of sealer on the muffler flange, a sleeve and a good clamp with proper bolts and brass nuts. Skip the copper gasket. They don't work for long.

Re: Looking for some advice....
 

Times 2!

Re: Looking for some advice....
 

It may be just that I'm viewing on my phone, but it appears your exhaust manifold has at least one hole in it above the clamp....

Re: Looking for some advice....
 

I agree with Steve Wastler, it looks like you're missing quite a bit of the clamp material and possibly some of the lower end of the manifold. Do you know if the lower end of the manifold has a good surface? If you open it up, you may either be patching or replacing the manifold if that surface is bad.

Re: Looking for some advice....
 

Thanks guys just went out and checked, definitely no holes, it's solid, I do think if I just tapped on the dried sealant that is on there it would probably just fall off. One of my concerns is if I do clean off the sealant there is something wrong under it and that's why my father-in-law used the sealant....I've been really enjoying the car this summer, driving her almost every day and she's running great, I don't want to get into something I can't easily get resolved and miss out on driving her.

Re: Looking for some advice....
 

Personally I would open it up and see just what the deal is with the "repair".
It's possible the fix is not going to be as simple as pulling it apart, cleaning it up and putting it back together. But... it just might be.
Lining up the muffler to the exhaust manifold can be a bit of a challenge especially when doing it solo. It is possible that your father in law just got frustrated trying to get it together and ended up slathering it up with a sealer. That would be the best discovery I would think.
It could be that the flange on the muffler is rusted, bent or missing some of it. In that case you can if your handy with a welder patch it up and make it work... for a while.
When you do get it sorted out and go to put the muffler back together use a floor jack to hold the muffler lightly against the manifold in order to allow you to get things lined up just right. Loosening the tail pipe clamp first will help in getting things lined up. After you get it lined up carefully lower the floor jack just enough to put a light bead of muffler sealant on the female flange of the muffler and jack it back into place against the manifold. Then put on your muffler clamp. Remember there is an up and a down on the clamp.
Having a second person to help line things up is a definite plus in doing this.
Taking the time to get it lined up perfectly is key in getting a long lasting seal.