The Ford Barn

The Ford Barn (https://www.fordbarn.com/forum/index.php)
-   Model A (1928-31) (https://www.fordbarn.com/forum/forumdisplay.php?f=3)
-   -   Shocks (https://www.fordbarn.com/forum/showthread.php?t=171404)

LopezCarguy 06-17-2015 09:08 PM

Shocks
 

Do shocks have same resistance up and down, in other words does shock dampen more on up stroke or down stroke??

RHD 06-17-2015 09:36 PM

Re: Shocks
 

Hi LopezCarguy.
The original type Houdaille shocks from new would have 10% in one direction (the downward stroke) and 90% the other.
I have tested NOS shocks and found them close to 5/95. Today if you can get a shock to perform at around 25/75 you are doing well. Many of the professionally restored shocks only obtain this resistance.
Best of luck.
Cheers,
Les.

updraught 06-18-2015 04:50 AM

Re: Shocks
 

Depends on whether you want a "performance" ride or a smooth ride. "Performance" shocks tend to be stiff in both directions for handling (at the expense of ride).

A "Koni Special D" shock, for example, has almost no resistance on compression (going over a bump), and the rebound is adjustable to "heaps" of resistance.

It is good for controlling a stiff spring as it allows it to compress quickly on a bump. The rebound resistance can then control the rebound (expansion) of the spring to create a smooth ride.

If you adjust the Koni up too much the wheels won't come down fast enough after a bump, and you will feel them leave the road. This is not good and it is then time to back them off a bit ...

Kurt in NJ 06-18-2015 08:24 AM

Re: Shocks
 

Moving the shock arm up should have much less resistance than moving it down----when I was rebuilding shocks for my car I found that with the adjusting valve closed the 2 foot handle would still move up, but could feel like it was stuck moving the lever down---then I opened the needle valve so it took about 60 seconds to move with about 50 lbs on the handle----there is an article in the model A service bulletins about rebuilding and setting shocks---the 50lbs and 2 foot lever was my interpetation of the tool in the service bulletins

fiddlybits 06-18-2015 09:17 AM

Re: Shocks
 

Now that everyone has explained how to build the clock in answer to the question "what time is it?"......

No, they do not have the same resistance up and down.

For more information.... see previous posts. :)

ericr 06-18-2015 10:57 AM

Re: Shocks
 

perhaps I mis-read it but two posts are contradictory as to what stroke requires greater resistance....

updraught 06-18-2015 07:18 PM

Re: Shocks
 

Quote:

The original type Houdaille shocks from new would have 10% in one direction (the downward stroke) and 90% the other.
Hey Les,

All my A shocks are like house bricks!

Is this 10% of full resistance on the downward (rebound) stroke?

Kurt in NJ 06-18-2015 08:01 PM

Re: Shocks
 

When you hit the bump and compress the spring you want the shock to let it move easy --to absorb the bump---after the bump the shock has to slow the rebound of the spring so you don't bounce

Mike V. Florida 06-18-2015 11:07 PM

Re: Shocks
 

Quote:

Originally Posted by RHD (Post 1105029)
Hi LopezCarguy.
The original type Houdaille shocks from new would have 10% in one direction (the downward stroke) and 90% the other.
I have tested NOS shocks and found them close to 5/95. Today if you can get a shock to perform at around 25/75 you are doing well. Many of the professionally restored shocks only obtain this resistance.
Best of luck.
Cheers,
Les.

This is the guy that literally wrote the book on Houdallie shocks.

Tudortomnz 06-18-2015 11:13 PM

Re: Shocks
 

If you want to know about & work on original Houdaille shocks, Les Pearsons book is invaluable.


All times are GMT -5. The time now is 09:07 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.