The Ford Barn

The Ford Barn (https://www.fordbarn.com/forum/index.php)
-   Early V8 (1932-53) (https://www.fordbarn.com/forum/forumdisplay.php?f=4)
-   -   part id..1932 or 1933/34 v8 ford (https://www.fordbarn.com/forum/showthread.php?t=273778)

FrankWest 12-08-2019 11:05 AM

part id..1932 or 1933/34 v8 ford
 

1 Attachment(s)
are these for 32 v8 or 33/34 v8 water inlet

deuce lover 12-08-2019 11:31 AM

Re: part id..1932 or 1933/34 v8 ford
 

'32 V8 bottom water inlets

Bored&Stroked 12-08-2019 11:36 AM

Re: part id..1932 or 1933/34 v8 ford
 

What he says! LOL

FrankWest 12-08-2019 11:43 AM

Re: part id..1932 or 1933/34 v8 ford
 

Does anyone have a picture of the 1933/34 water inlets

DavidG 12-08-2019 11:51 AM

Re: part id..1932 or 1933/34 v8 ford
 

They were also used initially on '33 V8s with front cross members that carried over the '32 spacing of the center lines of the motor mount insulators of 12". When that spacing was increased to 17" early in the '33 model year cast iron combined water inlet/motor mount brackets were adopted along with a new front cross member.

FrankWest 12-08-2019 12:06 PM

Re: part id..1932 or 1933/34 v8 ford
 

Thanks

DavidG 12-08-2019 12:37 PM

Re: part id..1932 or 1933/34 v8 ford
 

3 Attachment(s)
An early '33 right side motor mount bracket used in concert with the stamped steel water inlet in your photo is shown below along with the early '33 front cross member.
A right side cast iron combined water inlet/mount is shown in the left corner of third photo

deuce lover 12-08-2019 12:43 PM

Re: part id..1932 or 1933/34 v8 ford
 

1 Attachment(s)
Here are the '33.34 ones.Early '33 intlets are like the '32 as David indicated

FrankWest 12-08-2019 02:01 PM

Re: part id..1932 or 1933/34 v8 ford
 

Great info Thanks for all the details.

FrankWest 12-08-2019 03:09 PM

Re: part id..1932 or 1933/34 v8 ford
 

Thanks again

FrankWest 12-10-2019 07:18 AM

Re: part id..1932 or 1933/34 v8 ford
 

Quote:

Originally Posted by deuce lover (Post 1829495)
Here are the '33.34 ones.Early '33 intlets are like the '32 as David indicated

will the later one piece inlets/motor mounts block mounting holes compatible with the earlier two piece inlet and motor mount?

DavidG 12-10-2019 08:19 AM

Re: part id..1932 or 1933/34 v8 ford
 

The holes for the attachment for the water inlets/motor mounts were unchanged from '32 through '36.

FrankWest 12-10-2019 08:30 AM

Re: part id..1932 or 1933/34 v8 ford
 

Thanks


All times are GMT -5. The time now is 06:52 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.