The Ford Barn

The Ford Barn (https://www.fordbarn.com/forum/index.php)
-   Model A (1928-31) (https://www.fordbarn.com/forum/forumdisplay.php?f=3)
-   -   Can anyone validate some frame dimensions? (https://www.fordbarn.com/forum/showthread.php?t=210288)

ModelAJim 12-04-2016 02:39 PM

Can anyone validate some frame dimensions?
 

1 Attachment(s)
Anyone have a bare frame they can easy validate these measurements? See attached plan. Wheelbase should be 103 1/2 right? Also. Looking for distance from center of front axle to the front frame where it begins to taper and the same from centerline of rear axle to start of the rear taper. I appreaciate it guys! The Wescott plans i hear are not accurate. Thanks!

Manager 12-04-2016 03:16 PM

Re: Can anyone validate some frame dimensions?
 

Centre line to centre line 103 1/2 centre line to front taper 22 5/8 centre line to rear taper 33 7/8 Those widths seem to be right but I think the 49 1/2 to the bend point is way out. I have 52 7/16 but that's measured paralell to the rail so it would be slightly less but not 2 11/16 less I wouldn't think. Maybe double check that one?

SteveB31 12-04-2016 05:52 PM

Re: Can anyone validate some frame dimensions?
 

Go to wescottsauto.com frame measurments from 1909-0948.. Click on Tech. All the frame specs from 1909-1941 are on there, and you can print them out .

Steve @ Bert's

ModelAJim 12-04-2016 08:04 PM

Re: Can anyone validate some frame dimensions?
 

Thank you!

Manager 12-04-2016 09:16 PM

Re: Can anyone validate some frame dimensions?
 

Some off Wescotts measurements on the A frame are wrong. They don't even add up. The 32 one seems to be fairly right though.
Also I checked and the 52 7/16 I gave you along the rail from front centreline to bend point is right.

ModelAJim 12-05-2016 07:12 AM

Re: Can anyone validate some frame dimensions?
 

Great! Thanks again!

Res731 12-05-2016 01:03 PM

Re: Can anyone validate some frame dimensions?
 

Thee was a whole thread on dimensions. Im trying to decipher the correct ones to use.

https://www.fordbarn.com/forum/showth...ight=dimension

ModelAJim 12-05-2016 07:51 PM

Re: Can anyone validate some frame dimensions?
 

Thatss the point. Wescotts have been said alot that the measurements are not accurate. I would not use any. I want accuracy so that i can make a set of framerails.

Manager 12-06-2016 06:12 AM

Re: Can anyone validate some frame dimensions?
 

Hey Jim just to clarify the P.M. looking at your drawing now, that rear crossmember should be 7 1/2 inches not 9. That 9" would be correct if it were to the bottom of the main frame before it tapers. It's 5" from the top off the frame. The frame is 2 1/4 at the back.

BRENT in 10-uh-C 12-06-2016 04:07 PM

Re: Can anyone validate some frame dimensions?
 

1 Attachment(s)
Quote:

Originally Posted by ModelAJim (Post 1395376)
Thatss the point. Wescotts have been said alot that the measurements are not accurate. I would not use any. I want accuracy so that i can make a set of framerails.

Then you really need to purchase an A-5005-* print from the archives. I own three of the frame prints, and I can tell you there are major discrepancies with what numbers are floating out there. I suspect many of those were reverse engineered (drawn), and as such that is where the mistakes came from.


.


All times are GMT -5. The time now is 05:28 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.