New Seat for 29 Pickup
 

Where would You buy a New seat for a 29 Pickup?

Re: New Seat for 29 Pickup
 

Snyder’s

Re: New Seat for 29 Pickup
 

I assume you're talking seat springs/cushions?

LeBaron Bonney was the source and repop originator for Model A seat springs. They're gone now but others have stepped into the breach.

Before you take the big step, consider buying a seat bottom, but only the covering for the seat back - if this is possible.

As you buy and use the completed/stuffed/prepared cushions for the pickup trucks, the first thing you will notice as you sit in the drivers seat is how close the steering wheel is to your chest. People in those days simply were not as "large" as they are today - plus our "expectations" of space in an automobile has changed. We are simply used to driving more roomy cars (not to mention cup holders.)

I say buy the partial seat setup because you can use the seat bottom quite well, but a lot of larger drivers can benefit from a "thinner" seat back in the trucks. You take the prepared cover and using a piece of plywood as a back and 3" of foam to the same outline you fabric cover the foam and staple the cover to the plywood back. This is then used in the usual position giving the driver a more modern "feel."

Now this issue may not be a problem for you. Perhaps you're into judging, or unlike me you're not 6-3 tall. Or maybe your driving expectations are different than most. But it is (or was) a "users" option in the L-B days.

Another aspect which comes to mind with original format seats is that they're stuffed with padding certainly, but L-B used to use a layer of "granulated" filler which self-adheres certainly but can be pulled loose. Otherwise known as the "perfect mouse-insulation material." Mice, if they can access your car interior, or even if they can't, will remove the stuffing to be placed elsewhere - as in any confined space. Like your muffler, or your No. 3 engine cylinder where the exhaust valve was left open when the engine stopped the last time. (tell me how I know about these?)

My original format L-B truck seat cushions live in a large footlocker sized wooden storage box when they're not being used as protection against mice. This is a MUST DO when parking the car even for a few days.

Foam, on the other hand, is relatively mouse-resistant (not total), and can be bought in different "durometers" to effect different degrees of seat cushion. Your back might be made more cushy compared to a seat bottom which probably wants to be a bit stiffer.

Some suggestions from a "user."

Joe K

Re: New Seat for 29 Pickup
 

Re: New Seat for 29 Pickup
 

good advice Joe.

the pickups are a bit tight to sit in, for medium to large guys.

Re: New Seat for 29 Pickup
 

I have a used bottom spring and bought a new back spring for my '29 RPU, but need the cushion and covering/upholstery for it. Any suggestions where I can get that material? I've looked at various vendors to no avail. This is a modified driver, not a restoration, so I'm looking for something budget 'friendly'. Do it myself, or have it done?

Craig

Re: New Seat for 29 Pickup
 

https://www.classtiqueupholstery.com/

Just put in a Snyders 2"lower seat cushion spring into my '29 Open Cab Pickup, you will also need the 2" longer back spring if you don't do a foam back to get a bit more room front to back.

The 2" lower spring makes it easier to get in.

Re: New Seat for 29 Pickup
 

I put in a pair of Jeep CJ5 reproduction seats in my '31. Don't know how they would work in a '29, but for me they work just fine, sits lower and further back giving me a lot more room. (They were way cheaper than any other solution I could come up with.)

Re: New Seat for 29 Pickup
 

Re: New Seat for 29 Pickup
 

Find the furniture upholstery guy in town. He'll have or be able to get you the foam. A square chunk is fine it cuts easily with an electric carving knife.

I'm going the plywood and foam route for our 29 Coupe.

My upholstery is still nice so basically I'll just be shortening the sides.