Re: carburetor 13/32 deep well socket
 

Hello Bill

Glad that you are making this much needed socket. It is almost impossible to get the housings off with out one. I stated much earlier that I made one years ago and have been rebuilding carburetors for many years. I wish I could have bought one of yours years ago. Put me down for one. Thanks.

Dick Hansen

Re: carburetor 13/32 deep well socket
 

I did send you a pm carb guy, so you are on the list.

Bill

Re: carburetor 13/32 deep well socket
 

I will take a couple

Re: carburetor 13/32 deep well socket
 

I will take one also.

Re: carburetor 13/32 deep well socket
 

Confirmation...I still want one!

Re: carburetor 13/32 deep well socket
 

Thanks Bill.

Dick Hansen

Re: carburetor 13/32 deep well socket
 

Re: carburetor 13/32 deep well socket
 

NO thankyou Bill and your son for doing this.

Re: carburetor 13/32 deep well socket
 

Please put me down on your list for one socket also. Thanks!

Re: carburetor 13/32 deep well socket
 

Thank you DBF, sent you a pm to confirm.

Bill

Re: carburetor 13/32 deep well socket
 

I have had a number of people who are following this thread, contact me outside this thread. I believe I have confirmed with everyone. As long as you have received a pm or email from me confirming you are on the list, you will receive the sockets you have requested as soon as they are ready. If for some reason you have not received a confirmation from me, please let me know.

Thank you all for your interest,

Bill Haag

Re: carburetor 13/32 deep well socket
 

Please count me in for one of the Special Sockets.
Thanks.

Re: carburetor 13/32 deep well socket
 

Bill, I have not received a conformation for one special socket.

Re: carburetor 13/32 deep well socket
 

Put me down for one

Re: carburetor 13/32 deep well socket
 

Smog tech, I did send you a confirmation via private message. If you did not receive it there for some reason, consider this your confirmation for 1 socket as soon as they are complete.

Bill

Re: carburetor 13/32 deep well socket
 

Bill - I'd like to order 3; will send you a pm shortly.
Dave

Re: carburetor 13/32 deep well socket
 

Ok folks, minor update but I did say I would keep everyone updated throughout this process.

I did receive the specialized tooling for this project today. Not the blanks, just the tooling.

I have spent the last 3 hours setting up an open machine for doing the broach work/making the 6 point hex part of this project. I will have to take this setup down until I receive the blanks and actually do the work, but it looks as though tooling wise we are good to go.

The blanks have been ordered, just not sure yet when I will receive them. But as soon as we have them we will get underway with annealing and such so we can start making the sockets.

Thank you all once again for your interest, and I feel honored to be part of this.

Obviously to some of you folks this is probably irrelevant to some degree, but we are moving forward, and I for one am anxious to get these things done and in everyones hands who expressed interest.

Hope you all are doing well, and I will continue to update, even though minor, as this project proceeds.

One other thing I would like to mention. Since I have been on this site I have randomly checked out other threads/discussions. I would like to thank each and every one of you for not turning this thread into some sort of crazy discussion other than what it originally started out as.........a socket. Not a bunch of other crap......well of course other than the walmart socket set comment.

Anyway, thank you all, we will see this through within the next few weeks.

Bill

Re: carburetor 13/32 deep well socket
 

I would like one of the sockets....thanks!

Re: carburetor 13/32 deep well socket
 

Bill , Include me in your list for one also , and Thank You for all your time and work involved .
Dave

Re: carburetor 13/32 deep well socket
 

I still keep getting pm's regarding price and such for this socket from people just reading this thread. If you are new to this thread and have any questions regarding price and purchasing or what have you, please read back to post #65 where I posted the pricing and rough details regarding how we are going to go about this.

For all you folks already on the list, I have been amazed how much interest there is. What we thought was going to be maybe 20-25 sockets, as you can imagine if you have followed this post, has been blown out of the water. Needless to say we are going to make a rather substantial run at this point figuring there will probably be residual interest once word continues to spread.

I did check back into making these in quantity by a couple of reputable US manufacturers, however the minimum quantity would be 5000/10,000 pieces. Now there has been an unbelievable interest in these at this point, but no where close to supporting a run of 5000.

We are going to run 150, and more after that if interest warrants doing so. This will still barely pay for all the tooling and such, but as I said before, this is a labor of love and bragging rights more so than making money at this point.

Hope everyone is doing well, and again, thank you for your interest in this project.

Bill

Re: carburetor 13/32 deep well socket
 

Bill, I for one appreciate what you are doing for the rest of us with this socket.
I would also like to say, and I hope others might agree... you should not lose money on this! Doing it "as a labor of love and bragging rights" is great, but please cover your costs.
I would pay a few bucks more to help...who knows what you might come up with next that would help our hobby?

Re: carburetor 13/32 deep well socket
 

I appreciate your comments jax. I built in a few different things when announcing the price based on what the interest level appeared to be at the time. Believe me, if I didn't think I could recover my cost at least I would have already changed some things regarding pricing. The added level of interest has allowed me to purchase better/different tooling which I should still be able to recoup the cost on, and hopefully cut down my time to make 2 to 3 times or more the number of sockets we originally figured on. So basically, covering cost, but still a "labor" of love, lol.

In short, I think I will be fine on cost, and possibly even make a buck or 2 on any subsequent runs.

I will know for sure after I get the blanks and start running these things in the next week or so, lol.

And of course if there is any other need down the road that I may be able to help with, I am sure my father will sucker me in somehow, lol.

Hope everyone following this thread is doing well. I will keep you updated.

Bill

Re: carburetor 13/32 deep well socket
 

One other thing to add to this. Due to a certain legal agreement the most time consuming part of this will probably be that I am going to have to hand stamp each socket. Since I have no automated way of doing this, no two sockets will be the same. It will probably be myself and my 2 sons doing this, so you will all no doubt end up with individualized sockets, lol.

If by chance someone out there has an actual high dollar rotary steel stamping machine which will do this process for minimal cost, please let me know since I may be interested, but the personalized thing does have kind of a nostalgic ring to it which I think fits well with this project.

Bill

Re: carburetor 13/32 deep well socket
 

Things are moving slowly, but they are moving. The number of requests for sockets is very close to the first run limit. My son is concerned that not every socket will be perfect, so he may have to halt adding to the list until the first run is made. Hope all you followers of this thread are well.

Re: carburetor 13/32 deep well socket
 

Hi All,

Minor update on the sockets.

Obviously the biggest part of this project is broaching the 13/32 hex end of the sockets. Using the broach I had made, I was able to broach 65 of the sockets before the broach wear tolerance was such that the finish clearance for the socket was not acceptable.

I have two new broaches on the way, but will not have them until Monday of next week. Once I receive the broaches I can finish the remaining blanks and get ready for the next part of the process.

The 13/32 broaching process has gone as well as expected even though I had hoped the tooling would last more than 65 pieces.

In any event, once the 13/32 broaching is complete we will move on to the inside bore of the sockets for clearance on the gav housing tube, then some finish turning on the outside followed by stamping the identification on the barrels of the sockets.

I know everyone is probably anxious to get these things in hand, but it will be a few weeks yet, due to scheduling and such before I can have these things complete and ready to ship.

Thank you all for your interest, and hopefully patience at this point. The project is moving, but possibly not quite as quick as everyone including myself would like.

Hope everyone is doing well, and as always, please feel free to contact me with any questions or concerns you may have regarding this project.

Thank you,

Bill

Re: carburetor 13/32 deep well socket
 

I somehow missed this thread until now and would like very much to be added to the list for two sockets from the first, or second run if necessary.
Thanks for making this happen!
Dave

Re: carburetor 13/32 deep well socket
 

Hi
Would it be possible to put me on the list as well?

Thanks

Manuel in Oz

Re: carburetor 13/32 deep well socket
 

Patiently waiting for a neat new tool!

Re: carburetor 13/32 deep well socket
 

Thank you for your patience Ray. I guarantee the quality of this tool will be well worth it.

Thank you again,

Bill

Re: carburetor 13/32 deep well socket
 

Re: carburetor 13/32 deep well socket
 

Mike: I know the feeling. We all have been waiting and hoping for that big bite. I have taken the gav housing out of three carbs since I got the first socket and could not be happier. I am looking for more carburetors just to use this tool. My wife don't think I need any more cause she thinks 14 sidebowl carbs and 7 other regular carbs is enough. She just don't understand. Hang in there and start reeling in, we are coming down the short rows now. I would like to take this time to publicaly thank my son for taking on this project. THANKS KID, Love Dad

Re: carburetor 13/32 deep well socket
 

Maybe Mike just decided to go relax and do some fishing while he is waiting on the socket.

Bill

Re: carburetor 13/32 deep well socket
 

Another minor update.

While waiting for the new broaches, I bored all of the sockets to receive the gav housing stem over the weekend including the ones that have not been broached yet. The plan was to do the broach work, then bore, but I decided to try and get ahead of the game any way possible.

I received the new broaches Monday and tonight was able to randomly broach a few of the unbroached sockets which I had bored over the weekend. Fortunately it looks as though they will match up just fine.

My schedule is kind of hectic right now due to my two sons motorcycle racing season starting up as well as some courses I am taking, so I am not sure when I will get to broach the remaining 85 sockets for the first run, but hopefully still this week at some point.

Once the broaching is done I still have to do the outside finish, as well as stamping which will take quite a bit of time, then finish with heat treat.

Long story short, things are moving forward.

Hope everyone is well,

Bill

Re: carburetor 13/32 deep well socket
 

I'll be happy to test any you already have made. :cool: :D ;)

Re: carburetor 13/32 deep well socket
 

Well Mike,

I have some broached, and such, but they still need stamped and heat treated. I will make sure you get what you have ordered asap once they are completed, lol.

Bill

Re: carburetor 13/32 deep well socket
 

Can't blame me for wanting to jump the line.:rolleyes::D

Re: carburetor 13/32 deep well socket
 

Don't blame you one bit mike, lol. Might just have to make you your own personalized socket, lol.

Bill

Re: carburetor 13/32 deep well socket
 

seems to me that these used to be available on special order from Sears, that's where dad got his. Maybe they aren't anymore?...

Re: carburetor 13/32 deep well socket
 

oh gee, if Mr. Sears or Mr. Roebuck called me personally today, I would tell them I already made a commitment to a fellow that had already stuck his neck out to help the hobby....which is a lot more than what Sears is doing today. Incidentally, I would say the Model "A" hobby is in sounder shape than Sears itself is.

I'm not trying to sound like a wiseacre, just trying to emphasize we need to support those that support the hobby. Maybe on down the line he or someone else will come up with another much-needed tool for Model "A" service.

Re: carburetor 13/32 deep well socket
 

agree:::
plus they come with a LIFETIME guarantee from haag1332.....;)