The Ford Barn

Wick · 05-12-2014, 06:23 PM

This is one item I can scratch off my list now! Will put back into working condition. Came out of a Ford Dealership in Elkton Va. a long time ago.

Steve Jelf · 05-12-2014, 07:22 PM

Neat find, Fred. I would think that's a pretty scarce item.

jackdaron · 05-12-2014, 08:05 PM

Good find.Been looking for one for many years,no luck yet.

Farmallcub49 · 05-12-2014, 08:13 PM

Fred,

Nice find. Do you have any of the jigs for it? Somewhere I have prints for everything if you need them.

James Rogers · 05-12-2014, 08:39 PM

Wick, it looks just like mine including the missing jigs. BTW, the pins will just drive out through the bottom and you can replace them.

dumb person · 05-12-2014, 08:47 PM

Sponsored Links (Register now to hide all advertisements)

i might have a few pans that need to be straightened.

Royce P · 05-13-2014, 06:34 AM

That's on my need list. Nice score!!!

Wick · 05-13-2014, 08:42 AM

I will be looking for... the jig's or drawings to make this thing complete.
I did see some old post on the mtfca site of a few drawings.

The next thing on my list....... KRW transmission drum holder.

05-12-2014, 06:23 PM	#1
Wick Senior Member Join Date: May 2010 Location: Gwynn's Island Va Posts: 1,386	Found a Pan Jig/Table This is one item I can scratch off my list now! Will put back into working condition. Came out of a Ford Dealership in Elkton Va. a long time ago. Last edited by Wick; 09-29-2019 at 04:31 AM.

05-12-2014, 07:22 PM	#2
Steve Jelf Senior Member Join Date: Apr 2012 Location: Parkerfield KS Posts: 526	Re: Found a Pan Jig/Table Neat find, Fred. I would think that's a pretty scarce item.

05-12-2014, 08:05 PM	#3
jackdaron Senior Member Join Date: May 2010 Location: Brownsburg,In. Posts: 383	Re: Found a Pan Jig/Table Good find.Been looking for one for many years,no luck yet.

05-12-2014, 08:13 PM	#4
Farmallcub49 Senior Member Join Date: Jan 2011 Location: St Joseph,MN Posts: 278	Re: Found a Pan Jig/Table Fred, Nice find. Do you have any of the jigs for it? Somewhere I have prints for everything if you need them. __________________ 'OSO HANDY RESTORATIONS Specializing in Model T Fords 320-293-1953

05-12-2014, 08:39 PM	#5
James Rogers Senior Member Join Date: May 2010 Location: Asheville,NC Posts: 3,104	Re: Found a Pan Jig/Table Wick, it looks just like mine including the missing jigs. BTW, the pins will just drive out through the bottom and you can replace them. __________________ http://www.model-a-ford-4bangers.com/

05-12-2014, 08:47 PM	#6
dumb person Senior Member Join Date: Apr 2011 Location: South pacific island Posts: 1,724	Re: Found a Pan Jig/Table Sponsored Links (Register now to hide all advertisements) i might have a few pans that need to be straightened. __________________ <Link> This is how we roll<Link> "I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob Outcasts rules of old cars #1 Fun is imperative, mainstream is overrated #2 If they think it is impossible, prove them wrong #3 If the science says it impossible you are not being creative enough. #4 No shame in recreating something you never had #5 If it were not for the law & physics you would be unstoppable

05-13-2014, 06:34 AM	#7
Royce P Senior Member Join Date: May 2010 Location: Tulsa OK Posts: 476	Re: Found a Pan Jig/Table That's on my need list. Nice score!!!

05-13-2014, 08:42 AM	#8
Wick Senior Member Join Date: May 2010 Location: Gwynn's Island Va Posts: 1,386	Re: Found a Pan Jig/Table I will be looking for... the jig's or drawings to make this thing complete. I did see some old post on the mtfca site of a few drawings. The next thing on my list....... KRW transmission drum holder.