|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-10-2017, 08:27 PM | #1 |
Senior Member
Join Date: Oct 2016
Location: NorCal East Bay
Posts: 409
|
1937 crank pulley seal?
Hey fellas,
So my crank pulley is leaking so I assume it’s the seal. I recently purchased this but is it correct for my car? I understand that originally it had some sort of rope seal but I want to upgrade it so I don’t have any issue I’m the future. With that said will this kit work even though it says 49-53? Any mods I need to do to the crank shaft? |
12-10-2017, 09:56 PM | #2 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,527
|
Re: 1937 crank pulley seal?
In order to use the metal sleeve, you will need to remove a like amount from the crank pulley. No mods to the crank shaft.
|
Sponsored Links (Register now to hide all advertisements) |
|
12-10-2017, 10:01 PM | #3 |
Senior Member
Join Date: Oct 2016
Location: NorCal East Bay
Posts: 409
|
Re: 1937 crank pulley seal?
|
12-10-2017, 10:22 PM | #4 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,320
|
Re: 1937 crank pulley seal?
I would say if the OD of the pulley and the sleeve are exactly the same, no.
|
12-11-2017, 12:32 AM | #5 |
Senior Member
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
|
Re: 1937 crank pulley seal?
If the pulley isn´t worn it wil work fine...they can have kind of a valley in them from the ropeseal wearing against it.
Cutting the pulley depends on how they are built...some just have the contact area against the crank at the ends and you end up with a loose fitting pulley. A speedy sleeve might be a better option in that case. |
12-11-2017, 12:58 AM | #6 |
Senior Member
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,835
|
Re: 1937 crank pulley seal?
Sponsored Links (Register now to hide all advertisements)
__________________
Unfortunately, two half wits don't make a whole wit! |
12-11-2017, 09:28 AM | #7 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: 1937 crank pulley seal?
I think the sleeve that comes with the one-piece seal will not work on your pulley, i.e. too thick. But, as noted above, a speedy sleeve to cover the groves will do the trick and no more leaks!!!
Dick. |
12-11-2017, 12:39 PM | #8 |
Senior Member
Join Date: Oct 2016
Location: NorCal East Bay
Posts: 409
|
Re: 1937 crank pulley seal?
So here’s the crank pulley I have now. It fits over the crank shaft fairly tight but I’m able to slide it on and off without any tools and there is a very minut amount of wiggle if I wiggle it. I assume the metal sleeve won’t wrk with this type of fit. So my question is do I have the wrong rubber seal or will the one I have still work?
|
12-11-2017, 12:47 PM | #9 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 1937 crank pulley seal?
See the groove worn into the pulley seal area? You are going to have to address that issue.
|
12-11-2017, 01:26 PM | #10 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,527
|
Re: 1937 crank pulley seal?
Your rubber seal will work but as noted, you need to repair that groove worn in it.
|
12-11-2017, 01:30 PM | #11 |
Senior Member
Join Date: Oct 2016
Location: NorCal East Bay
Posts: 409
|
Re: 1937 crank pulley seal?
|
12-11-2017, 01:37 PM | #12 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: 1937 crank pulley seal?
Solo, I believe the speedy sleeve is your easiest way to provide a smooth surface for the new neoprene seal. It will cover up the groove. You drive the sleeve onto the pulley snout. It come with a "cap" to allow you to press the sleeve on.
Dick. |
12-11-2017, 01:50 PM | #13 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 1937 crank pulley seal?
You should be able to get a sleeve that will fit it with minor cleanup of your current surface.
|
12-11-2017, 02:02 PM | #14 |
Senior Member
Join Date: Oct 2016
Location: NorCal East Bay
Posts: 409
|
Re: 1937 crank pulley seal?
Awesome, do you have a link to the “speedy sleeve?”
|
12-11-2017, 02:23 PM | #15 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: 1937 crank pulley seal?
The full name of the ones I've used is SKF Speedi-Sleeve. Try www.skf.com and see if that gets you there.
Dick. |
12-11-2017, 02:28 PM | #16 |
Senior Member
Join Date: May 2010
Location: Southern Illinois
Posts: 3,795
|
Re: 1937 crank pulley seal?
Buy the replacement sleeve with no spiral groove cut into it. Then have someone machine off the old sleeve on your pulley in the equivalent length of the new smooth sleeve. the new sleeve can be welded to the original pulley, also. Any reputable machine shop can do this easily. Contact VanPelt sales for the replacement smooth sleeve.
|
12-11-2017, 02:29 PM | #17 |
Senior Member
Join Date: May 2010
Location: Southern Illinois
Posts: 3,795
|
Re: 1937 crank pulley seal?
|
12-11-2017, 03:54 PM | #18 | ||
Senior Member
Join Date: Oct 2016
Location: NorCal East Bay
Posts: 409
|
Re: 1937 crank pulley seal?
Quote:
Quote:
Last edited by Solo_909; 12-11-2017 at 04:53 PM. |
||
12-11-2017, 05:09 PM | #19 |
Senior Member
Join Date: May 2010
Location: Capital of Corruption , NY
Posts: 811
|
Re: 1937 crank pulley seal?
Speedi-sleeve by Chicago Rawhide. #99162. NAPA did sell them. Here it is. I used this one on my '51 Merc. Check size against yours.
https://www.napaonline.com/en/p/NOS99162 Install video https://www.youtube.com/watch?v=5XIjYuhxKsw |
12-11-2017, 06:44 PM | #20 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: 1937 crank pulley seal?
Solo, the install video that Tony referenced above will give you a better picture on how these thin sleeves work on our flat head pulleys. If you don't feel comfortable or have access to a micrometer to measure diameter and length of the area you need to repair, another option is to take your pulley to a machine shop and let them put the proper sized sleeve on for you. As to whether or not you can buy a new pulley, bear in mind that these were all intended to be used with the rope seal, so finding one that's set up for the new one piece might be a challenge.
Dick. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|