|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
10-24-2015, 08:34 AM | #1 |
Senior Member
Join Date: May 2013
Location: germany
Posts: 128
|
pinion and ratio 3,78 help
Hello
Today I wanted to change my new pinion 3.78. the old is a 4.11 Pinion. now the stock not fit. the inside diameter of the bearing is too large. Does anyone know exactly what I need to order for storage (which I have everything completely) nice would be the item numbers of Macs thank you |
10-24-2015, 08:35 AM | #2 |
Senior Member
Join Date: May 2013
Location: germany
Posts: 128
|
Re: pinion and ratio 3,78 help
the camp is installed the Timken 48-4621
|
Sponsored Links (Register now to hide all advertisements) |
|
10-24-2015, 08:36 AM | #3 |
Senior Member
Join Date: May 2013
Location: germany
Posts: 128
|
Re: pinion and ratio 3,78 help
on the new pinion 3,78 stand 9602
|
10-24-2015, 08:43 AM | #4 |
Senior Member
Join Date: May 2013
Location: germany
Posts: 128
|
Re: pinion and ratio 3,78 help
and how can I
Drive Pinion Bearing Double Race - Ford Remove from the housing |
10-24-2015, 08:54 AM | #5 |
Senior Member
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
|
Re: pinion and ratio 3,78 help
Some pics so we can identify what parts you got to start with and what new ones you got.
If its only the wrong bearings you got or is the ring and pinion different ? A parts and a shopmanual aint a to bad thing |
10-24-2015, 09:00 AM | #6 |
Senior Member
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,858
|
Re: pinion and ratio 3,78 help
Sponsored Links (Register now to hide all advertisements)
http://www.jalopyjournal.com/forum/t...o-axle.812569/
__________________
John "Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein |
10-24-2015, 09:22 AM | #7 |
Senior Member
Join Date: May 2013
Location: germany
Posts: 128
|
Re: pinion and ratio 3,78 help
here the picture
|
10-24-2015, 09:24 AM | #8 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: pinion and ratio 3,78 help
Might also help to provide the year of rear end you are working on.
|
10-24-2015, 09:28 AM | #9 |
Senior Member
Join Date: May 2013
Location: germany
Posts: 128
|
sorry here the right pic pinion and ratio 3,78 help
sorry 1 6/16 is correct!!!!!
|
10-24-2015, 09:29 AM | #10 |
Senior Member
Join Date: May 2013
Location: germany
Posts: 128
|
Re: pinion and ratio 3,78 help
ford coupe 1936
|
10-24-2015, 09:47 AM | #11 |
Senior Member
Join Date: May 2013
Location: germany
Posts: 128
|
Re: pinion and ratio 3,78 help
i ned this one
|
10-24-2015, 01:01 PM | #12 |
Senior Member
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
|
Re: pinion and ratio 3,78 help
The first one you have looks like something out of a quickchange rear has the shaft cut down for a supportbearing ??
|
10-24-2015, 01:39 PM | #13 |
Senior Member
Join Date: May 2010
Location: Southern France
Posts: 5,308
|
Re: pinion and ratio 3,78 help
Looks like the pinion has been machined down to take the 33-34 bearing set .Also as flatheadmurre mentioned the end for the driveshaft has been machined for possibly a quickchange setup.You will have to find another R & P set as you should not mix pinions with ring gears.
|
10-24-2015, 04:34 PM | #14 |
Senior Member
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,858
|
Re: pinion and ratio 3,78 help
Also, that pinion gear in your second picture has six splines. Most likely, your '36 driveshaft, if stock, would have 10 splines on its pinion end, and you would need a 10 spline pinion.
__________________
John "Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein Last edited by JM 35 Sedan; 10-24-2015 at 04:41 PM. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|