|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-07-2022, 05:49 AM | #1 |
Member
Join Date: May 2010
Location: South Australia
Posts: 50
|
Spark Plug Wire Holders
I plan to use the original spark plug wire holders on the 8BA I am building.
The engine I salvaged them from had all of the Left hand side (5-8) wires routed through both holders and all of the Right hand side loose. Does anyone have any pictures of the original layout ? |
02-07-2022, 08:06 AM | #2 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,950
|
Re: Spark Plug Wire Holders
Look through this thread and you will find and 8BA with a spark plug wire holders similar to yours. Even though the holders are a different style at their top, I think the routing is still the same.
https://www.jalopyjournal.com/forum/...dster.1194785/ Last edited by 19Fordy; 02-07-2022 at 11:07 AM. |
Sponsored Links (Register now to hide all advertisements) |
|
02-07-2022, 01:56 PM | #3 | |
Senior Member
Join Date: May 2015
Posts: 8,166
|
Re: Spark Plug Wire Holders
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
02-07-2022, 02:23 PM | #4 |
Member
Join Date: May 2010
Location: virginia
Posts: 39
|
Re: Spark Plug Wire Holders
There are directions and a "photo" on page 57 of the 49-51 shop manual.
Good luck. Russ Brown |
02-07-2022, 04:23 PM | #5 |
Member
Join Date: May 2010
Location: South Australia
Posts: 50
|
Re: Spark Plug Wire Holders
Thanks for the replies. Unfortunately I don't have a factory Manual.
Those pictures on that link 19Fordy do give a good indication of how they routed the wires. That basically reflects what I observed on the old engine I salvaged these from. These holders when removed were bent at odd angles as in the pictures although not so easy to discern. A side on shot would illustrate this better . I wonder if they have become bent over time? Those pictures would suggest that they should be straight up and down. |
02-07-2022, 04:28 PM | #6 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,950
|
Re: Spark Plug Wire Holders
Sponsored Links (Register now to hide all advertisements)
|
02-08-2022, 08:59 AM | #7 |
Senior Member
Join Date: May 2010
Location: Wildwood, MO. (near St. Louis)
Posts: 1,792
|
Re: Spark Plug Wire Holders
While doing research on the 49-51 Mercury at the Benson Ford Research center a while back, I came across this drawing of the 0BA-12290 Ign. Cable and bracket assembly. I hope that this helps.
|
02-08-2022, 10:09 AM | #8 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,950
|
Re: Spark Plug Wire Holders
Wow, Don, Thanks for posting that drawing.
|
02-08-2022, 03:48 PM | #9 |
Member
Join Date: May 2010
Location: South Australia
Posts: 50
|
Re: Spark Plug Wire Holders
Don, thanks for that illustration. Great find. Well done.
|
02-08-2022, 04:31 PM | #10 |
Member
Join Date: May 2010
Location: South Australia
Posts: 50
|
Re: Spark Plug Wire Holders
After some trial and error and some straightening of these brackets this is the arrangement I have come up with. Seems to achieve what is set out in the drawing.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|