Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-17-2011, 03:24 PM   #1
Ken Lauderback
Junior Member
 
Join Date: May 2010
Posts: 7
Default Gas gauge repair

Got in my '31 pickup this morning for the first time since last fall some time. The gas gauge was nearly on the "0" reading. I thought "I had more gas in here than that..." but decided I had been mistaken. So, off to the gas station to fill up. Only took 6 gallons, and the gauge is still on "O" so I assume the float has become soaked and sunk. When I "rebuilt" the gas gauge a couple of years ago, I think I coated the float with shellac. So, guessing the alcohol in the fuel has dissolved the coating. The reason I cleaned up the original gauge and reused it was that the so called "rebuild kit" I bought from Sacramento Vintage Ford at that time was so cheap looking and cheesy that I couldn't bring myself to put it in the tank. Are there different kits out there? If so, who makes the best one? Or, is there a good replacement for the original float? I'm probably not going to change it right now, but will need to do so some time this summer. Any help will be appreciated.
Thanks
Ken Lauderback is offline   Reply With Quote
Old 04-17-2011, 03:37 PM   #2
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Gas gauge repair

i just had the same thing a sunken cork float. i just changed mine out to the neoprene float hoping it will last longer. it can be installed on your original Gage
Mitch//pa is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-17-2011, 03:52 PM   #3
Mitch Bunkin in PA
Senior Member
 
Mitch Bunkin in PA's Avatar
 
Join Date: May 2010
Location: Pipersville,Bucks County,PA
Posts: 142
Default Re: Gas gauge repair

I had the same problem 4 1/2 years ago & like Mitch (above) replaced with neoprene.
Everything fine since then.
Regards.
"the other Mitch"
__________________
WEBSITE=http://faculty.bucks.edu/bunkinm/

"Most people ONLY want to know
what they already believe and
nothing more."
Mitch Bunkin in PA is offline   Reply With Quote
Old 04-17-2011, 06:40 PM   #4
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Gas gauge repair

GAS GUAGE FLOAT - NEOPRENEFor Year(s): 28-31

Gas and Alcohol proof float.




ill give it a try before i order one from NASA

Last edited by Mitch//pa; 04-17-2011 at 06:46 PM.
Mitch//pa is offline   Reply With Quote
Old 04-17-2011, 06:50 PM   #5
Aerocraft
Senior Member
 
Aerocraft's Avatar
 
Join Date: May 2010
Location: Naperville, IL
Posts: 1,387
Default Re: Gas gauge repair

What worked for me was to shorten a float that I removed from a modern car where I had changed the entire gas gauge. That assembly had been made to accommodate ethanol fuels. That float has been working well in my 40B for over five years. Gar Williams
Aerocraft is offline   Reply With Quote
Old 04-17-2011, 09:08 PM   #6
John Butts in CT
Senior Member
 
John Butts in CT's Avatar
 
Join Date: May 2010
Location: Southeastern Connecticut
Posts: 464
Default Re: Gas gauge repair

Sponsored Links (Register now to hide all advertisements)
Ken, this topic has been discussed several times since ethanol appeared at the pump. You might want to read https://www.fordbarn.com/forum/showthread.php?t=30531

What I think of as as the "hard" neoprene floats (per Mitch's post) have been offered by Model A vendors for years, as have the "soft" neoprene gaskets. I'm no chemist, but I suspect that the floats and the gaskets have a different makeup. My "hard" float is perfect after five years. My bad experience with the neoprene gaskets is chronicled in the earlier post.

Whatever float you choose, stick with cork gaskets, and keep a spare set on hand. It's much easier to replace your gaskets every so often than to deal with neoprene gaskets that have turned to goo and run down inside your tank.

JMHO. Best of luck. Let us know what you decide.
John Butts in CT is offline   Reply With Quote
Old 04-17-2011, 09:25 PM   #7
Model A Man
Senior Member
 
Model A Man's Avatar
 
Join Date: May 2010
Location: Sarasota Florida
Posts: 604
Default Re: Gas gauge repair

I have the brass float in both my A's and seem to work well. I bought them from one of the A vendors

I just checked Mikes afordable web site and they have the brass floats for $9.95 each
Model A Man is offline   Reply With Quote
Old 04-17-2011, 10:20 PM   #8
Ken Lauderback
Junior Member
 
Join Date: May 2010
Posts: 7
Default Re: Gas gauge repair

Thanks to all of you who have taken time to respond. It has been a big help!
Ken Lauderback is offline   Reply With Quote
Old 01-28-2017, 03:27 PM   #9
GearHeadDiver
Member
 
Join Date: Apr 2012
Location: Ontario, Canada
Posts: 60
Default Re: Gas gauge repair

I'm in the process or rebuilding mine..with a recently purchased kit
After cleaning, I was dry fitting all the components...to find that the 2 smaller cork gaskets (on either side of the glass) are a bit thick.....
Is it common practice to soak them in (?) before assembly?
As well, I've decided to re-finish the original face plate with the hole...as mine is eliptical...and the new one is round...
What is the best paint for the face? Lacquer? Or ?

Any help or input appreciated. ..
GearHeadDiver is offline   Reply With Quote
Old 01-28-2017, 07:24 PM   #10
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Gas gauge repair

I recall only using one cork gasket against the glass. Lacquer paint worked fine for me.

I reused my original oval plate after wire wheeling the old paint and using lacquer.
Tom Wesenberg is offline   Reply With Quote
Old 01-28-2017, 07:32 PM   #11
GearHeadDiver
Member
 
Join Date: Apr 2012
Location: Ontario, Canada
Posts: 60
Default Re: Gas gauge repair

Hmmmmm...when I took the original apart, it had one on either side of the glass...but we're considerably thinner....
The kit diagram shows one on either side of the glass...and is supplied with 2...
Hmmmmm.....

I think the original eliptical plate looks better.... still not fond of the "made in china" label on the bags...of the majority of repro parts I've purchased.
I'd really like to have original, patina'd parts....but not easy to find.
GearHeadDiver is offline   Reply With Quote
Old 01-28-2017, 07:34 PM   #12
daveymc29
Senior Member
 
daveymc29's Avatar
 
Join Date: Sep 2010
Location: Danville, CA
Posts: 1,550
Default Re: Gas gauge repair

I found that some of the kits, whether cork or neoprene, the gaskets are way too thick. All Ford in Campbell had the thin cork gaskets and I used a neoprene float. So far so good. for years I was using a brass float from a Tillotson carb, but for some reason it cracked and sank. I had to specify I wanted the thin cork and bought several sets. They were quite inexpensive, as I recall. Just hard to find.
daveymc29 is offline   Reply With Quote
Old 01-28-2017, 08:06 PM   #13
GearHeadDiver
Member
 
Join Date: Apr 2012
Location: Ontario, Canada
Posts: 60
Default Re: Gas gauge repair

I may just make a couple myself...out of thinner cork... if I can remember where I put it
GearHeadDiver is offline   Reply With Quote
Old 01-28-2017, 08:41 PM   #14
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Gas gauge repair

The parts book does show A-9324 as having two, so I guess I did use two gaskets after all. It's been quite a while since I've done a gas gauge, and I wasn't sure.
Tom Wesenberg is offline   Reply With Quote
Old 01-28-2017, 08:50 PM   #15
Tom Endy
Senior Member
 
Tom Endy's Avatar
 
Join Date: May 2010
Location: Southern California
Posts: 3,122
Default Re: Gas gauge repair

Reenee H. Kotas in San Diego makes and sells a good quality brass gas tank float that easily fits through the gauge opening. The last time we bought some from him they were $5.
858-278-8178

Tom Endy
Tom Endy is offline   Reply With Quote
Old 01-28-2017, 09:08 PM   #16
GearHeadDiver
Member
 
Join Date: Apr 2012
Location: Ontario, Canada
Posts: 60
Default Re: Gas gauge repair

Good to know....

I'm new to the "A" game...
Having fun so far.
Lots of great advice, tips, info and people here...
GearHeadDiver is offline   Reply With Quote
Old 01-28-2017, 09:37 PM   #17
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Gas gauge repair

I have not had a problem with the corks being to thick.. i have had a problem with the repo threads being off causing the outer and inner assy to not go together
Mitch//pa is offline   Reply With Quote
Old 01-28-2017, 09:48 PM   #18
GearHeadDiver
Member
 
Join Date: Apr 2012
Location: Ontario, Canada
Posts: 60
Default Re: Gas gauge repair

I'm using my original inner ring... I checked original glass to the new... same thickness, although slightly larger diameter...
with the thickness of the 2 cork rings... the inner ring only catches 2 or so threads... I'm not going to force it or try to compress the cork....I'll make 2 thinner ones...maybe..

Would there be a different kit for 28-29 versus 30-31?
GearHeadDiver is offline   Reply With Quote
Old 01-28-2017, 09:52 PM   #19
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Gas gauge repair

Same set::
Attached Images
File Type: jpg IMG_5697.jpg (18.1 KB, 152 views)
Mitch//pa is offline   Reply With Quote
Old 01-28-2017, 09:59 PM   #20
GearHeadDiver
Member
 
Join Date: Apr 2012
Location: Ontario, Canada
Posts: 60
Default Re: Gas gauge repair

Grrrrrrrr......
GearHeadDiver is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:47 PM.