The Ford Barn

Lawrie · 07-20-2016, 07:40 PM

I see that the Canadian transmissions that we have here in Australia and New Zealand have the funny rear thrust washer on the cluster gear.and they are not availible.
I thinking about make up some and would like see if any one else would like one.
Lawrie

Brian · 07-20-2016, 09:48 PM

Yep- how much?

Mac VP · 07-21-2016, 04:49 AM

Laurie, we did a small batch a couple years ago. Modified the 8M-7129 to match the same opening. You would still use the 8M-7128 thin washer next to it. We get $27.50 for both. Here is the picture comparison.

Lawrie · 07-21-2016, 05:49 AM

Mac, I have just drawn up a set of dimensions so I can make them on the mill, I used a nos one like the left one.
The nos one and a new thin washer still gave me .017 end float so will make some .005 thicker.
Lawrie

koates · 07-21-2016, 06:35 AM

Hi Lawrie, exactly which Canadian transmissions (models and years) are we talking about here ? Regards, Kevin.

Lawrie · 07-21-2016, 03:52 PM

Sponsored Links (Register now to hide all advertisements)

Kevin, I think its all the ones that were fitted to the Aussie and NZ cars,I,m not 100% if its the early trans ,but sure about the later ones.
Lawrie

danliveshere · 07-23-2016, 05:12 AM

Mac I think that was my sample washer I posted to you. Laurie is rebuilding this transmission for me now

07-20-2016, 07:40 PM	#1
Lawrie Senior Member Join Date: May 2010 Location: Qld, Australia Posts: 4,212	canadian transmission thrust washers I see that the Canadian transmissions that we have here in Australia and New Zealand have the funny rear thrust washer on the cluster gear.and they are not availible. I thinking about make up some and would like see if any one else would like one. Lawrie

07-20-2016, 09:48 PM	#2
Brian Senior Member Join Date: May 2010 Location: Masterton, New Zealand Posts: 3,830	Re: canadian transmission thrust washers Yep- how much? __________________ Unfortunately, two half wits don't make a whole wit!

07-21-2016, 04:49 AM	#3
Mac VP Senior Member Join Date: May 2010 Location: Cincinnati, OH Posts: 1,361	Re: canadian transmission thrust washers Laurie, we did a small batch a couple years ago. Modified the 8M-7129 to match the same opening. You would still use the 8M-7128 thin washer next to it. We get $27.50 for both. Here is the picture comparison. __________________ VANPELT SALES LLC Cincinnati, Ohio Office: 513-724-9486 www.vanpeltsales.com www.classictransmission.com

07-21-2016, 05:49 AM	#4
Lawrie Senior Member Join Date: May 2010 Location: Qld, Australia Posts: 4,212	Re: canadian transmission thrust washers Mac, I have just drawn up a set of dimensions so I can make them on the mill, I used a nos one like the left one. The nos one and a new thin washer still gave me .017 end float so will make some .005 thicker. Lawrie

07-21-2016, 06:35 AM	#5
koates Senior Member Join Date: May 2010 Location: Melbourne Australia. Posts: 2,078	Re: canadian transmission thrust washers Hi Lawrie, exactly which Canadian transmissions (models and years) are we talking about here ? Regards, Kevin.

07-21-2016, 03:52 PM	#6
Lawrie Senior Member Join Date: May 2010 Location: Qld, Australia Posts: 4,212	Re: canadian transmission thrust washers Sponsored Links (Register now to hide all advertisements) Kevin, I think its all the ones that were fitted to the Aussie and NZ cars,I,m not 100% if its the early trans ,but sure about the later ones. Lawrie

07-23-2016, 05:12 AM	#7
danliveshere Senior Member Join Date: Jul 2010 Location: Cairns , Australia Posts: 746	Re: canadian transmission thrust washers Mac I think that was my sample washer I posted to you. Laurie is rebuilding this transmission for me now