|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-10-2020, 05:26 PM | #1 |
BANNED
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
|
Soldering and Nickel Plating
I was wondering if I were to fill some small holes on a steel part with solder and smooth out the area that was soldered, will nickel plating adhear to the solder?
Thanks. Pluck |
05-10-2020, 05:28 PM | #2 |
Senior Member
Join Date: May 2010
Location: Wichita, Kansas
Posts: 710
|
Re: Soldering and Nickel Plating
If you use silver solder.
|
Sponsored Links (Register now to hide all advertisements) |
|
05-10-2020, 05:36 PM | #3 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Soldering and Nickel Plating
I have only seen and heard of copper being used.
__________________
"The more things change, the more they stay the same." |
05-11-2020, 12:44 AM | #4 |
Senior Member
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,354
|
Re: Soldering and Nickel Plating
Ask your plater
|
05-11-2020, 04:40 AM | #5 |
Senior Member
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
|
Re: Soldering and Nickel Plating
|
05-11-2020, 10:34 AM | #6 |
Senior Member
Join Date: May 2010
Location: Long Island, NY
Posts: 3,472
|
Re: Soldering and Nickel Plating
Sponsored Links (Register now to hide all advertisements)
Solder is lead, and lead was once a common body filler material. A quality nickle plating will have copper first. Copper adheres to lead. By the way, bullets have copper plating!
__________________
Bob Bidonde |
05-11-2020, 08:31 PM | #7 |
BANNED
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
|
Re: Soldering and Nickel Plating
I think I will use brass rod...it should flow ok.
Thanks. Pluck Last edited by Steve Plucker; 05-12-2020 at 07:37 AM. |
05-11-2020, 11:14 PM | #8 |
Senior Member
Join Date: Nov 2010
Location: Sedro-Woolley, WA
Posts: 1,023
|
Re: Soldering and Nickel Plating
I have been this route. My plater "Specialized Plating" in Mt. Vernon, WA will not plate over lead solder repairs. He will plate over Silver solder repairs, and about any other metal. He does nice work and in 50 years, my sliver solder pre-plating repairs have never let us down. Silver solder is not lead solder. Its price reflects this.
|
05-12-2020, 12:33 AM | #9 |
Senior Member
Join Date: May 2010
Location: Ogden Utah
Posts: 242
|
Re: Soldering and Nickel Plating
I have used silver solder in the past and then chrome plating process. Had to repair a set of lando arms so the extra cost was worth it.
|
05-12-2020, 07:06 AM | #10 |
Senior Member
Join Date: May 2010
Location: New Jersey
Posts: 734
|
Re: Soldering and Nickel Plating
I was doing a lot of research on plating in the now defunct CAR magazine (lots of copies saved) and found something about a type of solder which could be used to patch pits in pot metal before plating. Unfortunately I do not remember the name......
|
05-12-2020, 08:56 AM | #11 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Soldering and Nickel Plating
Brass works but takes around 850 degrees F. Silver is higher at around 1200 degrees F for the easy type. I usually braze stuff than needs repair for the plating process unless it's soft metal like zinc die cast. I have a special rod and flux for it (Muggy Weld).
A person needs to have the right flux and clean, clean, clean. There are different rod sizes too. The type of job designates the materials needed. I use oxy/acetylene to do most of this type stuff. Map gas and propane can work on some things but I like to get it hot quick and get the job done fast so that it doesn't bake the part too bad. You can't even tell it was soldered after the plating process. Of course, plating is all about how good the polish job is prior to going into the tanks. Plating might stick to the soft solders but the metal is too compressible. It can be easily damaged even if there is plating over it. The plating is generally very thin and the soft metal can yield under the plating if it gets bumped. Last edited by rotorwrench; 05-12-2020 at 09:02 AM. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|