|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-08-2012, 05:39 PM | #1 |
Member
Join Date: Sep 2010
Posts: 65
|
Model B Ford Dipper Tray
I have a fully pressurized B engine that is being assembled. The previous owner still has the dipper tray in the oil pan, but there is a 1/2 inch hole drilled in each rod/dipper trough to allow the oil to quickly drain back into the pan. The rods are inserted with the dipper scoops plugged. Do I have to leave the dipper tray in the pan, or since the rods are inserted and pressurized, can I not install the dipper tray? I am using a modified pump for the full pressure oiling.
|
04-08-2012, 05:43 PM | #2 |
Senior Member
Join Date: May 2010
Location: Naperville, IL
Posts: 1,387
|
Re: Model B Ford Dipper Tray
How about splash lubrication to the cylinder walls? How is that going to happen without the dipper tray? Are the rods drilled to spray oil on the walls ? Gar Williams
|
Sponsored Links (Register now to hide all advertisements) |
|
04-08-2012, 05:49 PM | #3 |
Member
Join Date: Sep 2010
Posts: 65
|
Re: Model B Ford Dipper Tray
I was thinking about that, but why would the previous owner drill the holes in the dipper troughs, wouldnt that keep them empty anyhow, or is the oil level enough to keep them full enough to spash the oil on the cylinder walls?
|
04-08-2012, 06:28 PM | #4 |
Member
Join Date: Aug 2010
Location: So Cal
Posts: 75
|
Re: Model B Ford Dipper Tray
Hey Dirttrack,,,
I'ed leave the pan in place,, Just for the fact it has the baffel in the bottom part of the tray...You should have plenty of oil coming off the pressurize "Rod"..That's the way a modern engine lube's the cyl. wall... I'ed run the oil pump shield they sell now too... Greg out West, |
04-08-2012, 08:18 PM | #5 |
Senior Member
Join Date: May 2010
Location: Austin, Texas
Posts: 925
|
Re: Model B Ford Dipper Tray
While we are talking B Dipper Trays, will a Model A Dipper Tray fit and function properly in a B Pan?
__________________
I noticed the harder I work the luckier I get! |
04-08-2012, 08:20 PM | #6 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model B Ford Dipper Tray
Sponsored Links (Register now to hide all advertisements)
|
04-08-2012, 11:17 PM | #7 |
Senior Member
Join Date: May 2010
Location: Anaheim California
Posts: 551
|
Re: Model B Ford Dipper Tray
My pressurized engines also have a hole in the dipper tray. I have many miles on them and the oil leaking out of the rods seems to be plenty to lube the cylinder walls, cam etc.
Leaving the pan in place with the holes allows the dipper tray to act as a "windage tray" in addition to reducing the drag of the dippers splashing through the puddle of oil, a presumed horse power advantage, small as it may be. The lower baffles may be an advantage to lubrication as mentioned previously. Some build a "dam" around the oil pump to prevent starving the oil pump on hard right turns like freeway on ramps. Richard Anaheim CA |
04-08-2012, 11:26 PM | #8 |
Senior Member
Join Date: Nov 2011
Location: B.C. Canada
Posts: 1,746
|
Re: Model B Ford Dipper Tray
Back in the 80s,I converted an A block to full pressure oiling with a drilled 33 CB shaft.I used a special oil pump & the dipper tray would no longer fit.I just left it out & had no problems & I didnt drill squirt holes in the rods.I put quite a few 1,000 miles on the engine before I sold it.These days,the 2-port Riley head is worth more than what I sold the whole engine for!
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|