|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-19-2017, 04:35 PM | #1 |
Senior Member
Join Date: May 2010
Location: Powell, TN
Posts: 2,509
|
fan belts 32-36
Last time I went thru this, bought script belts from Mac's and they did not fit. I finally bought a lawnmower belt at Walmart for the 32 with a later small gen pulley. This time I needed one for a stock 34, some vendors books say 55" but that would not work nor would a 56, it took a 57" that fit right. Got it from Rural King as a lawn mower and industrial belt for $5.99. The Walmart belt on my 32 is several years old and thousands of miles. Just wondered what others are doing for belts and what length they are using.
|
02-19-2017, 06:08 PM | #2 |
Senior Member
Join Date: May 2010
Location: Wildwood, MO. (near St. Louis)
Posts: 1,792
|
Re: fan belts 32-36
I used a Gates B54.....It's outer circumference is 57". See attached chart.
|
Sponsored Links (Register now to hide all advertisements) |
|
02-19-2017, 06:19 PM | #3 |
Senior Member
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,858
|
Re: fan belts 32-36
Good chart Don. The B54 belt is what someone had told me about 5 yrs ago. I just couldn't remember to reply to Jim until you jogged my memory with your post.
__________________
John "Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein |
02-19-2017, 06:33 PM | #4 |
Senior Member
Join Date: May 2010
Location: near Pittsburgh, PA
Posts: 403
|
Re: fan belts 32-36
I use the B54 from NAPA for '35 and '36.
|
02-19-2017, 07:26 PM | #5 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: fan belts 32-36
A lot depends on what pulley you have on water pumps, generator, and generator mount on intake/ height of intake.
Take the belt off, then measure around the pulleys with tape or rope. Take tape/rope/old belt down to parts place and get a rope the same length and width. Forget about numbers until you know you have all correct size pulleys, etc. My 2¢.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
02-20-2017, 01:27 PM | #6 |
Senior Member
Join Date: May 2010
Location: Powell, TN
Posts: 2,509
|
Re: fan belts 32-36
Sponsored Links (Register now to hide all advertisements)
|
02-20-2017, 04:30 PM | #7 |
Senior Member
Join Date: May 2010
Location: Mill Valley,Ca.
Posts: 1,509
|
Re: fan belts 32-36
If you want a belt length, take an old belt, any size. Cut it, measure length...
Put it around pulleys, etc. Measure the gap- or overlap- of the cut belt. Easy way to get around the pulleys. It's still awkward. Karl |
02-20-2017, 08:59 PM | #8 |
Senior Member
Join Date: Nov 2014
Location: New ringgold pa
Posts: 311
|
Re: fan belts 32-36
That is helpful thank you
__________________
Ford |
|
|
Sponsored Links (Register now to hide all advertisements) |
|