Go Back   The Ford Barn > General Discussion > Late V8 (1954+)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-10-2014, 11:21 PM   #1
elwood
Senior Member
 
elwood's Avatar
 
Join Date: May 2010
Location: Dallas
Posts: 1,046
Default 9 inch ID

Hey guys, I was given this 9 inch and am not sure what it is out of.
Its 57 inches from the inside to the inside of the backing plates.
Hoping someone could tell by the mounts on it.
It looks like it says 82 on the back side.
Thanks guys.
I want to order brake parts and drums for it and stick it in my 50 F1..
Need more pictures ?
Attached Images
File Type: jpg Picture 107.jpg (39.3 KB, 30 views)
File Type: jpg Picture 110.jpg (67.6 KB, 38 views)
File Type: jpg Picture 111.jpg (76.3 KB, 49 views)
File Type: jpg Picture 112.jpg (75.1 KB, 38 views)
elwood is offline   Reply With Quote
Old 08-10-2014, 11:25 PM   #2
Lanny
Senior Member
 
Lanny's Avatar
 
Join Date: May 2010
Location: Mn
Posts: 2,402
Default Re: 9 inch ID

Elwood, does it have 4 1/2" or 5 1/2" wheel bolt pattern ?









.
__________________
My Wife Says That I Never Listen to Her,
I Think That's What She Said


If mama ain't happy, ain't nobody happy.
But if daddy ain't happy...RUN
Lanny is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-10-2014, 11:32 PM   #3
elwood
Senior Member
 
elwood's Avatar
 
Join Date: May 2010
Location: Dallas
Posts: 1,046
Default Re: 9 inch ID

Hey Lanny, Its a 5 on 5 1/2
elwood is offline   Reply With Quote
Old 08-10-2014, 11:40 PM   #4
Lanny
Senior Member
 
Lanny's Avatar
 
Join Date: May 2010
Location: Mn
Posts: 2,402
Default Re: 9 inch ID

With the 5 1/2" bp, and the spring perches on Top of the axle housing,
the rear end is prolly out of a pickup or Econoline.
Is there an alum tag on one of the pumpkin studs yet, if so, it would
have some numbers on it.
Many of the pickup rears had 31 spline axles, pull one and count the splines.








.
__________________
My Wife Says That I Never Listen to Her,
I Think That's What She Said


If mama ain't happy, ain't nobody happy.
But if daddy ain't happy...RUN
Lanny is offline   Reply With Quote
Old 08-10-2014, 11:42 PM   #5
elwood
Senior Member
 
elwood's Avatar
 
Join Date: May 2010
Location: Dallas
Posts: 1,046
Default Re: 9 inch ID

Hey Lanny, Ill pull a axel and count tomorrow, and I think I can see a PU in the yellow wrecking yard marker on the back side ..
elwood is offline   Reply With Quote
Old 08-11-2014, 02:39 AM   #6
Alaska Jim
Senior Member
 
Alaska Jim's Avatar
 
Join Date: May 2010
Location: Palmer, Alaska
Posts: 1,573
Default Re: 9 inch ID

Sponsored Links (Register now to hide all advertisements)
take the metal tag on the 3rd member to your local Ford dealer parts dept., it has all the info on it you need. yr, ratio, model etc.
Alaska Jim is offline   Reply With Quote
Old 08-11-2014, 01:07 PM   #7
elwood
Senior Member
 
elwood's Avatar
 
Join Date: May 2010
Location: Dallas
Posts: 1,046
Default Re: 9 inch ID

there is no tag on it.
elwood is offline   Reply With Quote
Old 08-11-2014, 10:27 PM   #8
ford3
Senior Member
 
Join Date: Oct 2012
Location: oroville calif.
Posts: 1,453
Default Re: 9 inch ID

Elwood, my book shows its a rear end from 57 to 72 f100
ford3 is offline   Reply With Quote
Old 08-11-2014, 10:31 PM   #9
elwood
Senior Member
 
elwood's Avatar
 
Join Date: May 2010
Location: Dallas
Posts: 1,046
Default Re: 9 inch ID

Thanks ford3, can you tell me what your looking at to see that ?
elwood is offline   Reply With Quote
Old 08-11-2014, 10:37 PM   #10
ford3
Senior Member
 
Join Date: Oct 2012
Location: oroville calif.
Posts: 1,453
Default Re: 9 inch ID

its a site called (High Q Ties 9" Ford info), type that in your search box and it will take you to the site, a lot of info on 8", 8.8", and 9" ford rear ends
ford3 is offline   Reply With Quote
Old 08-12-2014, 11:21 PM   #11
Alaska Jim
Senior Member
 
Alaska Jim's Avatar
 
Join Date: May 2010
Location: Palmer, Alaska
Posts: 1,573
Default Re: 9 inch ID

Sorry, The one picture looked like it had the tag still on the one bolt near the top of the 3rd member. must be a brake line bracket or something else.
Alaska Jim is offline   Reply With Quote
Old 08-14-2014, 12:47 PM   #12
gearhead1952
Senior Member
 
gearhead1952's Avatar
 
Join Date: May 2010
Location: Julesburg, Colorado
Posts: 713
Default Re: 9 inch ID

Because of the ring gear bump on the back that means it is newer than 1960. Not sure the exact year they went from smooth back to the bump but for sure 60 was smooth. Are the brakes still on it? Does it have the cable that runs from the top pin down to the star wheel? Indicates self adjusting which came out in 66.
gearhead1952 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:03 PM.