Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-02-2015, 01:28 PM   #1
Kevin Marsh
Junior Member
 
Kevin Marsh's Avatar
 
Join Date: Apr 2012
Location: Riverton, Utah
Posts: 12
Default 1934 Pickup overheating issues

Hello all, I could use your help. I wrapped up the restoration on a 34 pickup a little over a year ago. The owner participated in a couple parades last summer, and each time the engine overheated and coolant boiled over.
The engine is a fresh rebuild by a very experienced flathead specialist, the radiator also received a new modern style core, new water pumps with the improved impellor design and the stock four blade fan. Total miles driven so far are 45, and on the open road the engine runs between 170 and 180 degrees.
I realize the engine will run cooler with more miles driven and a sufficient break in period, but for now I need to do something to aid during the extreme conditions during parades as I know he will be doing more of those this summer.
I have tried to research the thermostats made by Bob Shewman that fit into the upper hoses, that have been discussed in several forums. The majority of the posts relate to bringing the engine temperature up, because the vehicle run too cool and never quite get to operating temperature. I am wondering about their effectiveness in maintaining the temperature during slow driving conditions such as a parade.
Ideally, the thermostat should allow sufficient time for the water in the radiator to cool before it cycles back into the motor. From what I have read about the Shewman thermostats they have bypass holes to prevent a surge of pressure when they reach temperature and open. Will that limit the amount of cooling efficiency of the radiator?
I would appreciate any feedback from those who my have encountered a similar situation, or have experience with these thermostats. I found an email contact for Bob Shewman ([email protected]) and have sent him an inquiry as well with no response back, so I am wondering if that is no longer a valid contact. If anyone has his current information I would appreciate that as well.
Thank you for your assistance.
Attached Images
File Type: jpg 6-5-2013 205.jpg (95.9 KB, 33 views)
File Type: jpg 6-10-2013 007.jpg (65.9 KB, 30 views)
File Type: jpg 6-10-2012 017.jpg (79.5 KB, 59 views)
Kevin Marsh is offline   Reply With Quote
Old 03-02-2015, 02:15 PM   #2
bobH
Senior Member
 
Join Date: May 2010
Location: so cal, placerville, vegas
Posts: 1,394
Default Re: 1934 Pickup overheating issues

I dont see a fan or generator in pic... for whatever it's worth, and in addition to the usual comments & suggestions, I put on a 6-blade fan on my own 34, and it became a little more 'parade-friendly'.
my best choice, stay out of parades
just opinion
bobH is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-02-2015, 03:24 PM   #3
Henry/Kokomo
Senior Member
 
Henry/Kokomo's Avatar
 
Join Date: May 2010
Location: Kokomo, Indiana
Posts: 1,731
Default Re: 1934 Pickup overheating issues

If you haven't already done so, check the timing. Retarded timing will cause the engine to heat. That would show up at idle speeds quicker than at highway speed.
In addition to a 6 bladed fan, a fan shroud might also prove useful. Do you know how the block was cleaned, internally, at the time of rebuild? That can make a difference, too.
__________________
Henry
Henry/Kokomo is offline   Reply With Quote
Old 03-02-2015, 03:29 PM   #4
G.M.
Senior Member
 
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
Default Re: 1934 Pickup overheating issues

Quote:
Originally Posted by Kevin Marsh View Post
Hello all, I could use your help. I wrapped up the restoration on a 34 pickup a little over a year ago. The owner participated in a couple parades last summer, and each time the engine overheated and coolant boiled over.
The engine is a fresh rebuild by a very experienced flathead specialist, the radiator also received a new modern style core, new water pumps with the improved impellor design and the stock four blade fan. Total miles driven so far are 45, and on the open road the engine runs between 170 and 180 degrees.
I realize the engine will run cooler with more miles driven and a sufficient break in period, but for now I need to do something to aid during the extreme conditions during parades as I know he will be doing more of those this summer.
I have tried to research the thermostats made by Bob Shewman that fit into the upper hoses, that have been discussed in several forums. The majority of the posts relate to bringing the engine temperature up, because the vehicle run too cool and never quite get to operating temperature. I am wondering about their effectiveness in maintaining the temperature during slow driving conditions such as a parade.
Ideally, the thermostat should allow sufficient time for the water in the radiator to cool before it cycles back into the motor. From what I have read about the Shewman thermostats they have bypass holes to prevent a surge of pressure when they reach temperature and open. Will that limit the amount of cooling efficiency of the radiator?
I would appreciate any feedback from those who my have encountered a similar situation, or have experience with these thermostats. I found an email contact for Bob Shewman ([email protected]) and have sent him an inquiry as well with no response back, so I am wondering if that is no longer a valid contact. If anyone has his current information I would appreciate that as well.
Thank you for your assistance.
Kevin. I just called Bob Shewman and he never got you email, said he checks several times a day. Call him at 1-610-933-6637. As long as the engine runs in the 160 range your OK. Thermostats have nothing to do with cooling, just make the engine run hotter. It looks like you have no problem driving at traveling speeds. This is not a parade vehicle in the summer the stock fan just don't produce enough air. Going down the road cooling air is produced by forward motion and in a parade there is not much of that. A shroud and a 6 bladed fan will do the trick, I'm not into electric fans so I can't help in that area. Getting the front of the fan about a 1/2" from the radiator helps some but not enough for parades. I have a 39 P/U with Skips high flow pumps, Bob Shewman's 180 degree stats in the hoses an industrial 6 blade fan, a shroud and Skips 3 lb overflow valve. This truck ran in the flea market at a National Ford V/8 show in Maryland in 2006 at a fast idle for over 2 hours and never got over 180. This was on a day that was over 100 degrees outside. If I raced it a little the temperature came down a little. You need a 4 lb pressure cap that seats down in the bottom of the filler neck and seals or Skips 3 lb check valve the go's on the bottom of the over flow tube. What the pressure cap or 3 lb valve does is closes off the over flow tube so water backing up in the top radiator tank don't back up in the tank do to the restriction of the 144 tubes and free flow out the over flow tube. Now you are also low on water. The cap or valve allows the radiator to remain filled to the top for maybe a year or more with out refilling. These caps and valve also let the pumps push the water through the radiator. Three things make for better cooling, more water in the system, more water forced through the radiator and more air through the radiator. This is all pretty well proven by your problem. G.M.
Attached Images
File Type: jpg PRESSURE VALVE 2.jpg (18.9 KB, 10 views)
__________________
www.fordcollector.com
G.M. is offline   Reply With Quote
Old 03-02-2015, 05:31 PM   #5
jimTN
Senior Member
 
Join Date: May 2010
Location: Powell, TN
Posts: 2,503
Default Re: 1934 Pickup overheating issues

I have a 59AB 60 over with HC heads in my 34 PU with an original rad core. Stock fan and exhaust wedge dividers. It runs very cool. Tried it without the fan and it still ran cool on the road but began to heat in stop and go traffic.
jimTN is offline   Reply With Quote
Old 03-02-2015, 06:40 PM   #6
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: 1934 Pickup overheating issues

Sponsored Links (Register now to hide all advertisements)
You need a good rubber sealed cap .the high flow pumps will pressurise the top tank and drive the water out the over flow .you can place a valve there or a heeder tank .by keeping the tempt lower with a shroud you more likely keep the water in .Thermostats will impede performance in hot weather .
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:11 AM.