Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-27-2012, 01:38 PM   #1
grump
Junior Member
 
Join Date: May 2010
Posts: 20
Cool ballast resistor

Hi, I just bought a 1948 pickup 8ab engine that is suppose to be rebuilt. I want to start it on a engine stand. Is there a resistor before the coil, and will a resistor from a 55 chevy work? I apologize to all the guys that gave me leads for my touring parts, I lost my job so I have cut back on my spending. Jim
grump is offline   Reply With Quote
Old 04-27-2012, 01:48 PM   #2
George/Maine
Senior Member
 
George/Maine's Avatar
 
Join Date: May 2010
Location: Mid coast Maine
Posts: 1,878
Default Re: ballast resistor

I,m guessing its 6 volt,55 chevy is 6 volt and 6 volt coil could use as is.No Resister.
George/Maine is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-27-2012, 01:54 PM   #3
sonny
Senior Member
 
sonny's Avatar
 
Join Date: Oct 2010
Location: Mantua, Ohio
Posts: 269
Default Re: ballast resistor

55 chevy is 12 volt.
sonny is offline   Reply With Quote
Old 04-27-2012, 01:56 PM   #4
sonny
Senior Member
 
sonny's Avatar
 
Join Date: Oct 2010
Location: Mantua, Ohio
Posts: 269
Default Re: ballast resistor

55 ford is 6 volt.
sonny is offline   Reply With Quote
Old 04-27-2012, 02:57 PM   #5
jan bogert
Senior Member
 
jan bogert's Avatar
 
Join Date: Nov 2011
Location: whitehall pa.
Posts: 439
Default Re: ballast resistor

Sonny, you are correct, 55 chevy is the first year for 12 volt in chevy. and thier 265 v8. it won't hurt if you put one on the coil.
jan bogert is offline   Reply With Quote
Old 04-27-2012, 03:05 PM   #6
Seth Swoboda
Senior Member
 
Seth Swoboda's Avatar
 
Join Date: May 2010
Location: Southern Illinois
Posts: 3,744
Default Re: ballast resistor

Sponsored Links (Register now to hide all advertisements)
I will have to agree based on experience, I'd put a resistor ahead of the coil. Test the resistor you have, around 1.5 ohms should be good. Also, sometimes the coil will say to use a resistor.
Seth Swoboda is offline   Reply With Quote
Old 04-27-2012, 04:02 PM   #7
George/Maine
Senior Member
 
George/Maine's Avatar
 
Join Date: May 2010
Location: Mid coast Maine
Posts: 1,878
Default Re: ballast resistor

If your are using a 6 volt battery,and have a round coil that is 6 volt,no resister is needed.
If you have a 12 volt battery you need a 12 volt coil and 1.5ohm resister.
George/Maine is offline   Reply With Quote
Old 04-27-2012, 04:21 PM   #8
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: ballast resistor

I don't know about the GM & other makes but FoMoCo used the same coil well up into the 12-volt era. The 12-volt vehicles used a ballast to control the amperage to the coil where the 6-volt vehicles didn't need one. The late type (1948/49 & later)round can coils were an improvement in technology and could take more heat than the old plastic covered iron core coils could.
rotorwrench is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:47 AM.