|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
|
08-20-2013, 07:28 AM | #1 |
Senior Member
Join Date: Jul 2010
Location: United Kingdom
Posts: 1,443
|
12v to 6v drop down resistors
Why do you need to use a different ( and more expensive) resistor for the horn and wiper when converting to 12v. Why can't you use the same cheapo type that is used for the coil?
|
08-20-2013, 07:35 AM | #2 |
Senior Member
Join Date: May 2010
Location: Lindenhurst, IL
Posts: 792
|
Re: 12v to 6v drop down resistors
Because the horn and wiper use more current. More current with the 6 volt drop is a larger watt resistor which dissipates more heat than the cheapo.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-20-2013, 08:09 AM | #3 |
Senior Member
Join Date: May 2010
Location: Kalamazoo
Posts: 1,656
|
Re: 12v to 6v drop down resistors
Using Ohm's law, V = I R or R = V/I, to get a 6V drop across the resistor if your horn uses 6 amps current, R = 6/6 = 1, so, you want a 1 ohm resistor (adjust accordingly for whatever current, I, your horn draws.
The power dissipated by the resistor would be I-squared x R, or, for this example, 36 x 1 = 36 watts. Probably could get by with less, unless you're planning on continuously laying on the horn or the resistor is going to be located with no ventilation. The wiper will require a lot less. Last edited by steve s; 08-20-2013 at 08:22 AM. |
08-20-2013, 08:30 AM | #4 |
Senior Member
Join Date: Jul 2010
Location: United Kingdom
Posts: 1,443
|
Re: 12v to 6v drop down resistors
So the 3 resistors are only different in their physical size and their ability not to fry up with too many amps through them?
|
08-20-2013, 09:57 AM | #5 | |
Senior Member
Join Date: May 2010
Location: Young Harris, GA
Posts: 1,821
|
Re: 12v to 6v drop down resistors
Quote:
The value of the resistor you use (the ohms) and the wattage needs to be specific to the thing you are connecting to the resistor to get the 6 volts you desire.
__________________
Jim Cannon Former MAFCA Technical Director "Have a Model A day!" |
|
08-20-2013, 10:08 AM | #6 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: 12v to 6v drop down resistors
Sponsored Links (Register now to hide all advertisements)
|
08-20-2013, 02:27 PM | #7 | |
Senior Member
Join Date: May 2010
Location: Young Harris, GA
Posts: 1,821
|
Re: 12v to 6v drop down resistors
Quote:
Ceramic ballast resistors are about 1.5 ohms. Either should work about the same, if what you need is 1.5 ohms. Hook one up and measure the voltage you get when you have the thing running that is connected to it (horn, wiper, etc.). It is somewhat counter-intuitive, but the less current draw the device has (horn, wiper, etc.) the larger the resistor needs to be to get you the final 6 volts that you want when that thing is running.
__________________
Jim Cannon Former MAFCA Technical Director "Have a Model A day!" |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|