|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-04-2018, 04:38 PM | #1 |
Senior Member
Join Date: Oct 2015
Location: Bonita, CA
Posts: 1,374
|
Flathead On Engine Stand
Does the exhaust type stand adapter and its bolts safely support the weight of a full dressed flathead? Anybody have problems with this set up?
|
11-04-2018, 04:42 PM | #2 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 3,271
|
Re: Flathead On Engine Stand
Yes, that's probably the best way . The entire engine can be built except for the one exhaust manifold.
|
Sponsored Links (Register now to hide all advertisements) |
|
11-04-2018, 07:36 PM | #3 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Flathead On Engine Stand
Yes, that is the best approach. On a 58ba it is not really an issue, but on the earlier blocks with the integral half bellhousing it is.
|
11-04-2018, 08:04 PM | #4 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,974
|
Re: Flathead On Engine Stand
An 8BA can hold the full weight of complete engine using bellhousing.
Do not use a 3 legged engine stand. It must have have 4 casters. I removed some parts to do some work on it Full engine was there at the start. Last edited by 19Fordy; 11-04-2018 at 08:39 PM. |
11-06-2018, 02:45 PM | #5 |
Member
Join Date: Jan 2015
Location: afton ny
Posts: 52
|
Re: Flathead On Engine Stand
Why not a three leg
|
11-06-2018, 03:09 PM | #6 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,974
|
Re: Flathead On Engine Stand
Sponsored Links (Register now to hide all advertisements)
Last edited by 19Fordy; 11-06-2018 at 03:17 PM. |
11-06-2018, 04:34 PM | #7 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Flathead On Engine Stand
The three leg stand issue is not specific to flatheads, any engine is unstable when using them.
|
11-06-2018, 05:30 PM | #8 | |
Senior Member
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,781
|
Re: Flathead On Engine Stand
Quote:
|
|
11-06-2018, 06:26 PM | #9 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,638
|
Re: Flathead On Engine Stand
They must have printed the picture backwards and then wrote on it....I like the price!!!...Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
11-06-2018, 07:30 PM | #10 |
Senior Member
Join Date: Jul 2018
Location: Ms GulfCoast
Posts: 238
|
Re: Flathead On Engine Stand
Speaking of Flatty engine stands; it seems to be getting very hard to find someone that makes these adapters or the "cradle like" brackets for flatheads, the one vendor "stumpy's fab works" seems to be non responsive and vern tardell seems to be out of them too, anyone know of vendors that make the side adapters or stands?
__________________
Regards, Todd 1936 FORD Tudor Slantback "cajunhotrodder" on instagram/youtube |
11-06-2018, 07:32 PM | #11 |
Senior Member
Join Date: Oct 2015
Location: Bonita, CA
Posts: 1,374
|
Re: Flathead On Engine Stand
That's all I have is 3 legged ones. Never had an issue before with up to a Ford 460 on them. That's probably double what a flathead weighs.
|
11-06-2018, 08:05 PM | #12 | |
Senior Member
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,973
|
Re: Flathead On Engine Stand
Quote:
(804) 245-1959 Cheers Tony |
|
11-06-2018, 10:05 PM | #13 |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 5,012
|
Re: Flathead On Engine Stand
Some of us here have welded a piece of angle iron about 20" long onto the plate that comes with the engine stand. The 'legs' of the angle are welded to the plate so the 45 degree face is where you bolt the engine. I just set an exhaust manifold on the angle before welding and drilled through the holes. No machine work, no math. It's great that these V8s are built at a 45 degree angle. If you don't weld, I bet a local shop would do it for a very small fee if you had the metal drilled, paint sanded off etc. I checked into the adapters and 65 bucks or so.
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1946 Tonner Pickup with 226 H six, 1979 Toyota landcruiser wagon, now wearing 1947 Ford Jailbar sheet metal. 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
11-06-2018, 10:46 PM | #14 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,974
|
Re: Flathead On Engine Stand
Yes, that is the ultra, ultra rare 8BA prototype engine. It is the only one made by "misprinting" the negative. I never noticed that photo error before after all these years. I still have the engine but, now it's "normal". Thanks for noticing.
|
11-06-2018, 11:13 PM | #15 | |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 5,012
|
Re: Flathead On Engine Stand
Quote:
Are you old enough to remember the old guy on a tricycle on Rowan and Martin's 'Laugh in'?
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1946 Tonner Pickup with 226 H six, 1979 Toyota landcruiser wagon, now wearing 1947 Ford Jailbar sheet metal. 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
|
11-06-2018, 11:14 PM | #16 |
Senior Member
Join Date: Dec 2012
Location: Payette, ID
Posts: 942
|
Re: Flathead On Engine Stand
Never ever had a problem with 3 legged stand. But I do not go off road with it
|
11-06-2018, 11:26 PM | #17 |
Senior Member
Join Date: Dec 2012
Location: Payette, ID
Posts: 942
|
Re: Flathead On Engine Stand
Speaking of three legged stands https://www.youtube.com/watch?v=QQh56geU0X8
|
11-07-2018, 11:39 AM | #18 |
Senior Member
Join Date: May 2010
Location: Millersport, central ohio
Posts: 668
|
Re: Flathead On Engine Stand
The much aligned Harbor Freight sells a motor stand that works very well. It is reasonable price, probably china made.( I gave up not buying made China stuff ) It has 2 wide legs and 2 not so wide ones in front. I made a exhaust attachment for it but used to hang 35-36 blocks by the bell housing with no problem. Even hauled a couple to the rebuilder 20 miles over not so smooth road.
|
11-07-2018, 12:55 PM | #19 |
Senior Member
Join Date: May 2010
Location: Salina, Utah
Posts: 328
|
Re: Flathead On Engine Stand
Regarding the side mount adaptors, Specialty Ford in Rosemead, California has them. 626 288 2121.
Wayno
__________________
Life is not a spectator sport. |
11-07-2018, 03:23 PM | #20 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,974
|
Re: Flathead On Engine Stand
Yup. I hung a complete 354 HEMI on one HF stand. Supported the front of the engine
with two 2 x4's and a 2x6 straddling the legs just to be safe. I know it's not a flatty but, one must admit it's pretty. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|