Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-03-2012, 01:00 PM   #1
Texas Tom
Senior Member
 
Texas Tom's Avatar
 
Join Date: May 2010
Location: Texas
Posts: 137
Default GRAIN-IT-TECHNOLOGIES woodgraining

I decided to use a kit from Grain-It-Technologies to apply woodgrain to the dash and window moldings of the 1930 Town Sedan that I'm restoring.

I think the 'factory-correct' Model A woodgrain pattern looks great. But for this car I decided I wanted something a bit more stylish, so I chose a burl pattern rather than the traditional horizontal pattern used in Model A's.

I had never before tried woodgraining, so I was prepared for 'so-so' results. The pieces turned out better than I had expected...and not too shabby for a first-timer. Attached are photos of the dash piece. It will look better after it's clear-coated, wet-sanded and buffed.

Using the kit is fairly easy and the work goes quickly. But practice using the roller is time well spent!

The only downside of using the Grain-It system is that drying time is extensive. Even with daily high temperatures in my garage of 90+ degrees, it took about a week for the ink (the graining pattern) to fully dry.

I know there are many ways to apply woodgrain. There's even a water-transfer process available today. (It's the same system used for several years to apply camouflage to guns, bows, and other hunting gear.) And there are commercial woodgrainers who I'm sure do an excellent job.

I have absolutely no connection with Grain-It other than being a one-time customer. If you're planning a woodgraining project, you may wish to consider their system. They offer a dozen or so patterns, including the factory-correct Model A pattern.
Attached Images
File Type: jpg Woodgrained dash 5 (Medium).jpg (24.6 KB, 319 views)
File Type: jpg Woodgrained dash 1 (Medium).jpg (37.0 KB, 299 views)
Texas Tom is offline   Reply With Quote
Old 09-03-2012, 01:24 PM   #2
Charles Coe
Senior Member
 
Charles Coe's Avatar
 
Join Date: May 2010
Location: Pace, FL near Pensacola
Posts: 374
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Wow! That looks great! I've looked at their website and wondered how difficult it would actually be.
Charles Coe is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-03-2012, 01:25 PM   #3
1931 flamingo
Senior Member
 
1931 flamingo's Avatar
 
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,389
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Does anyone have pictures of original wood grain for a 31?? At a recent show there were about a dozen A's, se3veral with wood grain. I realize no tow were exactly alike but those that had it no two really came close to each other.
Thanks
Paul in CT

Forgot to mention how "rich" and nice a job you did ! ! !

Last edited by 1931 flamingo; 09-03-2012 at 01:41 PM. Reason: add
1931 flamingo is offline   Reply With Quote
Old 09-03-2012, 01:27 PM   #4
Ross/Kzoo
Senior Member
 
Ross/Kzoo's Avatar
 
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

You did a great job. That really looks nice. Looks like did very good prep work.
Ross/Kzoo is offline   Reply With Quote
Old 09-03-2012, 01:44 PM   #5
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Tom,
Beautiful job, even without clearcoat! I plan on doing some graining, whatever the "grain" I make, somewhere in the world, their's a "grain" that's the same!
Before selling my all black '30 coupe, I considered a greyish/silver grain on interior trim pieces, and call it "BLACK EBONY!"
On the same car, I once "considered" doing all the reveal mouldings in the factory type mahogony type grain. (Poor man's WOODIE!) Bill W.
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 09-03-2012, 02:19 PM   #6
Special Coupe Frank
Senior Member
 
Special Coupe Frank's Avatar
 
Join Date: May 2010
Location: Northeast Penna
Posts: 2,108
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Sponsored Links (Register now to hide all advertisements)
I am pretty sure that the "plate grain / roller transfer" process is the same or nearly the same as the original lithographing process used back in the 1920's-1950's.

Very nice work, Texas Tom !

SC Frank
Special Coupe Frank is offline   Reply With Quote
Old 09-03-2012, 02:37 PM   #7
FL&WVMIKE
Senior Member
 
FL&WVMIKE's Avatar
 
Join Date: May 2010
Location: Daytona Beach, Fl & Spencer, W. Va,
Posts: 4,442
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Texas Tom ........................
That walnut burl is very close to the 1934 Ford walnut burl finish. I believe that the 1934 Ford used a little more black in their design. It seems to be about 50% covered with the black. Here is a photo of an original 1934 Ford ashtray.
MIKE
CLICK ON PHOTO TO ENLARGE - Twice
Attached Images
File Type: jpg ashtray.jpg (43.1 KB, 110 views)
FL&WVMIKE is offline   Reply With Quote
Old 09-03-2012, 03:17 PM   #8
Special Coupe Frank
Senior Member
 
Special Coupe Frank's Avatar
 
Join Date: May 2010
Location: Northeast Penna
Posts: 2,108
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Suggestion on the clear-coat - might consider a satin-lacquer... the really high gloss looks too much like a "poured-finish" bar table-top for my taste...

( Your results may vary....)

SC Frank
Special Coupe Frank is offline   Reply With Quote
Old 09-03-2012, 03:24 PM   #9
TinCup
Senior Member
 
TinCup's Avatar
 
Join Date: May 2010
Location: OKC / Tonkawa, Ok.
Posts: 1,977
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

The new oil base ink is the only way to go. I have used both and the oil based ink is much easier to work with IMO. What did you use for base color? Camera makes these look different but they are the same.
Attached Images
File Type: jpg IMG01142-20120627-2045.jpg (69.1 KB, 176 views)
File Type: jpg IMG01139-20120626-1723.jpg (55.4 KB, 171 views)
TinCup is offline   Reply With Quote
Old 09-03-2012, 03:24 PM   #10
Huckster Dave
Senior Member
 
Join Date: Sep 2011
Location: Ronan, Montana
Posts: 158
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Good job, I like it. Both of them.
Huckster Dave is offline   Reply With Quote
Old 09-03-2012, 03:59 PM   #11
Texas Tom
Senior Member
 
Texas Tom's Avatar
 
Join Date: May 2010
Location: Texas
Posts: 137
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

The photo posted by TIN CUP depicts what I understand to be 'factory-correct' woodgrain for a Model A. I presume his photo on the left looks more blonde in tone due to the close proximity of the camera flash.

GRAIN-IT offers a wide selection of graining plates, each with a different pattern. As I recall, they state that anyone with their entire set of plates can replicate the factory-correct graining of nearly 90% of U.S. autos made in the 1930s - 1950s.

The base coat on my woodgraining is mahogany. As I recall, GRAIN-IT offers two shades of mahogany, and the one I used is labeled MH-1.

The guy who runs (owns?) GRAIN-IT is Evan Westlake. He's a straight shooter, and very willing to assist the customer in selecting the base color and the grain pattern to fit the 'look' that the customer is seeking.

I found the process makes it pretty easy to achieve good results.
Texas Tom is offline   Reply With Quote
Old 09-03-2012, 04:01 PM   #12
TinCup
Senior Member
 
TinCup's Avatar
 
Join Date: May 2010
Location: OKC / Tonkawa, Ok.
Posts: 1,977
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

I spoke to Evan several times and he was a big help. Yes the plate I used is his mahoganey plate.
TinCup is offline   Reply With Quote
Old 09-03-2012, 08:11 PM   #13
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Both woodgrain jobs are beautiful.
Tom Wesenberg is offline   Reply With Quote
Old 09-04-2012, 12:54 AM   #14
Mike V. Florida
Senior Member
 
Mike V. Florida's Avatar
 
Join Date: May 2010
Location: South Florida
Posts: 14,054
Send a message via AIM to Mike V. Florida
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Quote:
Originally Posted by TinCup View Post
I spoke to Evan several times and he was a big help. Yes the plate I used is his mahoganey plate.
here
Attached Images
File Type: jpg SNV33248.JPG (229.7 KB, 80 views)
__________________
What's right about America is that although we have a mess of problems, we have great capacity - intellect and resources - to do some thing about them. - Henry Ford II
Mike V. Florida is offline   Reply With Quote
Old 09-04-2012, 03:52 AM   #15
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

i like it
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Old 09-04-2012, 04:22 PM   #16
The Woodgrain Man
Junior Member
 
Join Date: Sep 2012
Location: Evan from Winter Haven, FL
Posts: 2
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Thanks to all of you on "THE FORD BARN" for posting the good results you are having with our tools! All your work looks Excellent!
I am very appreciative of this "WORD OF MOUTH" response.

I want to take this opportunity to let you all know that I am always happy to help, in whatever way I can, with any of your Woodgraining projects.

Thanks Again!

Sincerely,
Evan Westlake
Grain-It Technologies
The Woodgrain Man is offline   Reply With Quote
Old 09-04-2012, 04:43 PM   #17
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,484
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Quote:
Originally Posted by The Woodgrain Man View Post
Thanks to all of you on "THE FORD BARN" for posting the good results you are having with our tools! All your work looks Excellent!
I am very appreciative of this "WORD OF MOUTH" response.

I want to take this opportunity to let you all know that I am always happy to help, in whatever way I can, with any of your Woodgraining projects.

Thanks Again!

Sincerely,
Evan Westlake
Grain-It Technologies
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 09-04-2012, 05:31 PM   #18
msmaron
Senior Member
 
msmaron's Avatar
 
Join Date: May 2010
Location: Wauconda, IL
Posts: 3,600
Send a message via AIM to msmaron
Default Re: GRAIN-IT-TECHNOLOGIES woodgraining

Quote:
Originally Posted by The Woodgrain Man View Post
Thanks to all of you on "THE FORD BARN" for posting the good results you are having with our tools! All your work looks Excellent!
I am very appreciative of this "WORD OF MOUTH" response.

I want to take this opportunity to let you all know that I am always happy to help, in whatever way I can, with any of your Woodgraining projects.

Thanks Again!

Sincerely,
Evan Westlake
Grain-It Technologies
Welcome to the Ford Barn
__________________
Mark Maron
Ill., Region MARC & MAFCA
MARC JSC Member MAFFI Trustee
National Facebook Admin.
https://www.facebook.com/groups/MARC.group/

A7191-Sport Coupe
29 Roadster
29-Town Sedan
29-Original Special Coupe
msmaron is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:55 AM.