|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-10-2021, 06:12 AM | #121 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here are the 35-36 pictures. Again, with thanks to others on this thread.
|
04-10-2021, 06:19 AM | #122 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here are the LB pictures. I realize I don't have a picture of the main bearing stud spacing (looks about 3 1/4 when measuring center to center with your tape measure or scale), which is my go-to way of IDing an LB. This deficiency is particularly egregious since I could have done so last month at the Chickashaw swap meet. My apologies.
In the picture with the two oil pans the left pan is from an LB and the right pan is from a Babbitt motor. |
Sponsored Links (Register now to hide all advertisements) |
|
04-10-2021, 06:21 AM | #123 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here are the 37-38 late 21 stud pictures.
|
04-10-2021, 06:24 AM | #124 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here is the 1938 only 24 stud picture (note short crank, 24 studs, and pencil test):
|
04-10-2021, 06:27 AM | #125 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here are the 39-40 Ford (221 cubic inches) pictures:
|
04-10-2021, 06:29 AM | #126 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Sponsored Links (Register now to hide all advertisements)
|
04-10-2021, 06:45 AM | #127 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here are the 41-42 Ford (221 cubic inches) pictures:
I don't have a picture yet! Working on it... |
04-10-2021, 06:56 AM | #128 | |
Senior Member
Join Date: May 2010
Posts: 196
|
Re: Engine block I.D. pictures
Quote:
|
|
04-10-2021, 06:56 AM | #129 |
Senior Member
Join Date: May 2010
Posts: 196
|
Re: Engine block I.D. pictures
Core clean out plugs
|
04-10-2021, 07:10 AM | #130 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here are pictures of 41-42 Mercury (239 cubic inch) blocks:
|
04-10-2021, 07:12 AM | #131 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
I don't have pictures of World War 2 era blocks. Instead I'll post pictures of two blocks damaged by hanging them only from the thin cast on bell housing from modern engine stands. I'm not saying this will happen to your engine if you do this, but it might.
|
04-10-2021, 07:16 AM | #132 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here are pictures of "59 series" 46-48 engines:
|
04-10-2021, 07:18 AM | #133 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,658
|
Re: Engine block I.D. pictures
Here are pictures of 49-53 8BA blocks:
|
04-10-2021, 07:47 AM | #134 |
Senior Member
Join Date: May 2010
Location: Powell, TN
Posts: 2,511
|
Re: Engine block I.D. pictures
Cannot get any of the pics to enlarge, when clicked on, this msg comes up:
<Error> <Code>AccessDenied</Code> <Message>Access Denied</Message> <RequestId>33KWSJ9Z8RTVGNJE</RequestId> <HostId>EoZtdOwJKaR9UxBoeFMQYGY2l7X/ZHNCeHEF56kTgPMRkahg8oLki7f0yItrjlEmpvvt0q/B19A=</HostId> </Error> |
04-10-2021, 07:52 AM | #135 |
Senior Member
Join Date: May 2010
Location: Powell, TN
Posts: 2,511
|
Re: Engine block I.D. pictures
Opps, see further down 28 cpe corrected the problem with new pics.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|