|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-24-2023, 12:02 PM | #1 |
Senior Member
Join Date: Sep 2021
Location: Point Loma, San Diego, CA
Posts: 425
|
"Re-using" previously torqued head studs
I'm in the middle of changing heads on my '41 flathead and am replacing the bottom two rows with longer ones, bolts actually. Now that the bottom two rows are off, the heads go on and off pretty easily without interference.
What are your thoughts on just keeping the top rows of long studs in place and reusing them to avoid the aggravation of removing studs? I know with more modern engines, studs are pretty 'special' and the recommendation is not to reuse a head stud that's already been torqued once. What about flatheads? Does the same concern exist? Should head studs not be re-used once they've torqued? |
08-24-2023, 12:38 PM | #2 |
Senior Member
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,047
|
Re: "Re-using" previously torqued head studs
Head studs have been reused over and over as long as they are not stretched, deformed or rusted badly. If you already have removed them it’s fine to replace with new ones but if they are still in and not visibly compromised I personally would not take a chance of breaking some off trying to remove. Just my 2cents.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-24-2023, 12:54 PM | #3 |
Senior Member
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,407
|
Re: "Re-using" previously torqued head studs
I vote for reusing the long studs if they are in good shape. You always run the risk of breaking a stud when you attempt to remove them.
|
08-24-2023, 09:41 PM | #4 | ||
Senior Member
Join Date: Sep 2021
Location: Point Loma, San Diego, CA
Posts: 425
|
Re: "Re-using" previously torqued head studs
Quote:
Quote:
At the risk of selective listening, you're telling me what I want to hear. But: no one has volunteered a different opinion. |
||
08-24-2023, 09:49 PM | #5 |
Senior Member
Join Date: Apr 2019
Location: Kansas
Posts: 943
|
Re: "Re-using" previously torqued head studs
The studs used on the flatheads are completely different than the "torque to yield" design bolts/studs on modern engines. Our old studs are intended to be reused as long as they are undamaged. New stuff is designed to stretch beyond reuse spec once tightened and are intended to be replaced each use.
Terry
__________________
"It don't take but country smarts to solve the problem" (Smokey Yunick) '41 Merc Town Sedan / 260" 8CM engine '66 Fairlane four door / "warmed up" 302 |
08-24-2023, 10:42 PM | #6 |
Senior Member
Join Date: Sep 2016
Location: Melbourne Australia
Posts: 542
|
Re: "Re-using" previously torqued head studs
Sponsored Links (Register now to hide all advertisements)
The only concern I have about leaving studs in place is its more fiddly to get a clean surface for the head gasket. |
08-25-2023, 12:46 AM | #7 |
Senior Member
Join Date: May 2010
Location: Minnesota
Posts: 1,832
|
Re: "Re-using" previously torqued head studs
Based on past experience; I would rather clean around studs than remove studs.
|
08-25-2023, 07:33 AM | #8 |
Senior Member
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,102
|
Re: "Re-using" previously torqued head studs
I would not have a problem using the original studs - especially in a street engine. The hardest part is the cleaning of the deck surface. On the bolts, make sure you use a really good thread sealer.
Personally, I think it will look a bit strange to have 1/2 studs and 1/2 bolts - but that is just me. Also, I like to torque head fasteners on the fine-threaded ends of studs - one just gets smoother readings and more reliable torque figures. But again - this isn't a supercharged race engine - so you'll probably be fine. |
08-25-2023, 08:08 AM | #9 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,195
|
Re: "Re-using" previously torqued head studs
Brad, if you don't like the looks of the nut and bolt head combination, you can always dress them up with chrome acorn covers!!!...(I've always felt they make the engine run better anyway!!)
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|