|
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
![]() |
Thread Tools | Display Modes |
![]() |
#81 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,800
|
![]()
Nice job, Rock.
|
![]() |
![]() |
![]() |
#82 |
Senior Member
Join Date: Sep 2021
Location: Marlboro, NY
Posts: 112
|
![]()
Changed the oil & filter, installed new plugs, cut excess park brake cable( had to make my own rear cable set), cleaned off the auto trans id plate so I can order a new pan gasket. Started the engine and let it warm up. Everything done in the yard, up on Jack stands. Got my exercise, but my wife says I don't walk enough... I'll be 80 this fall. Ha Ha!! JPL
|
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#83 |
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 4,053
|
![]() |
![]() |
![]() |
![]() |
#84 |
Senior Member
Join Date: Jan 2015
Posts: 331
|
![]()
I woke our 38 convertible coupe up from a long winters nap; hooked battery up; put a little gas in carb,started right up, went for a warm up drive, aired up tires, and cleaned white walls; ready for AUburn
|
![]() |
![]() |
![]() |
#85 |
Senior Member
|
![]()
Bought another one!
__________________
Tim Carlig |
![]() |
![]() |
![]() |
#86 |
Senior Member
Join Date: May 2012
Location: Fredericksburg, Virginia
Posts: 811
|
![]() Sponsored Links (Register now to hide all advertisements)
This is one of the best small swap meets on the east coast. So who is going? I'll have my table set up at Wick's spot along the treeline. Stop by and say high. Steve |
![]() |
![]() |
![]() |
#87 |
Senior Member
|
![]()
You do nice work, Steve.
__________________
Tim Carlig |
![]() |
![]() |
![]() |
#88 | |
Senior Member
Join Date: May 2015
Posts: 8,579
|
![]() Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
![]() |
![]() |
![]() |
#89 |
Senior Member
Join Date: Feb 2020
Location: Paducah Ky
Posts: 291
|
![]()
Luray's in Virginia, right?
Al Hook |
![]() |
![]() |
![]() |
#90 |
Senior Member
Join Date: May 2012
Location: Fredericksburg, Virginia
Posts: 811
|
![]() |
![]() |
![]() |
![]() |
#91 |
Senior Member
Join Date: May 2012
Location: Fredericksburg, Virginia
Posts: 811
|
![]()
Nobody working on a flathead V8 lately? I just got back from Luray where I sold some '35 Ford parts and refurbished original Ford cutouts.
|
![]() |
![]() |
![]() |
#92 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,800
|
![]()
Just put some new front wheel cylinders on my 41 pickup. Rear ones will be done when the new ones get here.
|
![]() |
![]() |
![]() |
#93 |
Senior Member
Join Date: May 2010
Location: South Texas
Posts: 1,722
|
![]()
Last week I helped swap the banjo section, ring & pinion, on a 40 pickup axle. The pins holding the coupler to the driveshaft and pinion had snapped due to worn out splines (the pins were taking the driving load and failed). We replaced the 4.11 with worn out splines for 3.78 with nice splines, good teeth, and nice bearings.
|
![]() |
![]() |
![]() |
#94 | |
Senior Member
Join Date: May 2015
Posts: 8,579
|
![]() Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
![]() |
![]() |
![]() |
#95 |
Senior Member
Join Date: May 2012
Location: Fredericksburg, Virginia
Posts: 811
|
![]()
I just posted a new video about installing and seating generator brushes. The example is for a model A generator, but the same process applies to flathead V8s. Some of you may find it helpful. There are many other generator related videos on my youtube channel as well.
https://youtu.be/1NiBylwzJ2s?si=fo3ulDRBBsYXHjGw |
![]() |
![]() |
![]() |
#96 | |
Member
Join Date: Sep 2020
Location: Hooper, Utah
Posts: 92
|
![]() Quote:
Dale |
|
![]() |
![]() |
![]() |
#97 |
Senior Member
Join Date: May 2012
Location: Fredericksburg, Virginia
Posts: 811
|
![]()
Must be a slow week...
![]() |
![]() |
![]() |
![]() |
#98 |
Senior Member
Join Date: Apr 2019
Location: Kansas
Posts: 1,009
|
![]()
My ol' flathead is just running so well that all I do is drive it!
![]()
__________________
"It don't take but country smarts to solve the problem" (Smokey Yunick) '41 Merc Town Sedan / 260" 8CM engine '66 Fairlane four door / "warmed up" ![]() |
![]() |
![]() |
![]() |
#99 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,448
|
![]()
I just got back from Florida and found the battery in my '51 was dead (the battery tender somehow got disconnected when I let the hood down last fall). I hooked up an old style charger (the maintainer wouldn't start) and am hoping it'll come back. With the price of Optima's these day, I hope it's not kaput.
|
![]() |
![]() |
![]() |
#100 |
Senior Member
Join Date: May 2012
Location: Fredericksburg, Virginia
Posts: 811
|
![]()
I just finished rebuilding this really nice, original paint 1940 generator. I'll be bringing it and other rebuilt generators and cutouts to the Richmond Virginia AACA meet this Saturday.
|
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|