Forum: Early V8
08-25-2017, 12:33 PM
|
|
Replies: 0
Views: 1,601
snap-on growler MT326C
have snap-on armature growler model MT326C and need operating instructions. this unit is the type with transformer "v" block and two sets of pencil leads 2red and 2black. would appreciate any...
|
|
Forum: Early V8 (1932-53)
02-06-2016, 10:46 PM
|
|
Replies: 4
Views: 1,074
|
|
Forum: Early V8 (1932-53)
02-06-2016, 04:57 PM
|
|
Replies: 4
Views: 1,074
1939 59 engine
have customer with 59fh pressed on cam gear. is it possible to change gear w/o removing cam from engine? thanks rfv60
|
|
Forum: Early V8
08-15-2011, 08:47 AM
|
|
Replies: 0
Views: 1,063
wtb 1946 to 48 ford coupe
wanted to buy 46 to 48 ford cpe. stock suspension and v8 flathead. prefer proper engine for vehicle. no basket cases or rust buckets. must be driveable and have have clear proper title. cash in hand...
|
|
Forum: Model A (1928-31)
04-21-2011, 06:21 AM
|
|
Replies: 3
Views: 1,416
help: not model a
am in desperate need of lg spline clutch disc for 1936 ihc pu 3spd c-1. would even consider one that needed to be rebuilt. don't have exact specs as to diameter but can supply when we talk. any...
|
|
Forum: Early V8 (1932-53)
11-07-2010, 03:40 PM
|
|
Replies: 50
Views: 10,117
|
|
Forum: Early V8 (1932-53)
10-13-2010, 06:15 AM
|
|
Replies: 20
Views: 4,240
Re: VANPELT parts, yes,or no
yes vote on my part. few times i've dealt w/mac offered great service, advice, and quality parts. has geat tranny book also!
|
|
Forum: Early V8 (1932-53)
09-13-2010, 07:29 AM
|
|
Replies: 25
Views: 6,345
|
|
Forum: Early V8 (1932-53)
07-31-2010, 08:14 AM
|
|
Replies: 1
Views: 1,395
scrub-a-dub. cast iron prep
been covered b4 but can't locate info on procedures and products to use for cleaning block/head cast iron parts for painting. appreciate the help. thank you
|
|
Forum: Early V8
07-17-2010, 04:14 PM
|
|
Replies: 0
Views: 1,024
Piloted reamer wanted 11/32 x 3/8
wanted piloted reamer-- the style used to do cast iron valve guides. 11/32 pilot and 3/8 ream. (.343 X .375). usually hs 5/16 square hex top side to fit gear reduction unit. have tried, goodson,...
|
|
Forum: Late V8
07-17-2010, 04:01 PM
|
|
Replies: 0
Views: 1,377
PILOTED REAMER wanted 11/32 X 3/8
l@@king to purchase piloted reamer---------the style used to ream cast iron valve guides. 11/32 pilot x 3/8 ream. (.343 X .375.) usually has 5/16 square hex top side.
have checked several supply...
|
|
Forum: Late V8 (1954+)
06-21-2010, 07:12 PM
|
|
Replies: 9
Views: 4,152
Re: boss 302---help me out here
thanks milt for the response, realize that. like i stated in a previous post did hope i would run past individual that had run down that road.
|
|
Forum: Late V8 (1954+)
06-21-2010, 03:22 PM
|
|
Replies: 9
Views: 4,152
Re: boss 302---help me out here
appreciate the responses. cyl wear is little if any: very little taper or out of round. customer has had this car since 6 months new and shows 60k on speedo. still has factory exhaust on it.
most...
|
|
Forum: Late V8
06-21-2010, 11:12 AM
|
|
Replies: 0
Views: 1,793
boss 302 pistons
1970 boss mustang 302. std 4.00 bore. approx: 5.15 rod length, 1.6 comp height, .910 pin. either cast or forged-- factory or aftermarket. need not be hi comp. any leads would be appreciated. thank...
|
|
Forum: Late V8 (1954+)
06-21-2010, 11:03 AM
|
|
Replies: 9
Views: 4,152
boss 302---help me out here
searching for replacement pistons (std) 1970 boss mustang 302 with 4.00 bore. present units all cracked on skirts. cylinder wall wear good. info as to any factory or aftermaket products would be...
|
|
Forum: Late V8 (1954+)
05-28-2010, 05:25 PM
|
|
Replies: 1
Views: 2,046
223 6cyl rocker shaft oiling
customer has 50's ford pu with oil supply problem to rocker shaft. need help locating online a diagram of oil system. do not have repair manual handy and vehicle is located 20 miles from shop. would...
|
|
Forum: Late V8 (1954+)
05-15-2010, 04:08 PM
|
|
Replies: 9
Views: 2,866
|
|
Forum: Late V8 (1954+)
05-13-2010, 09:47 PM
|
|
Replies: 9
Views: 2,866
|
|
Forum: Late V8 (1954+)
05-13-2010, 06:36 PM
|
|
Replies: 9
Views: 2,866
1970 boss 302 mustang
have customer with '70 boss owned since new. 59k miles. most pieces as henry built it including factory exhaust. been sitting in confined garage 8 years now time to bring it back 2 life. not looking...
|
|
Forum: Early V8 (1932-53)
05-07-2010, 05:41 PM
|
|
Replies: 4
Views: 3,231
modern stuff
well we will see how it works. thanks for letting it continue.; v860 is 4 sale. 608 726 0210
|
