Forum: Early V8
03-22-2022, 01:59 PM
|
Replies: 0
Views: 405
|
Forum: Early V8 (1932-53)
03-11-2022, 03:48 PM
|
Replies: 48
Views: 4,895
Re: 1932 potential buy
The serial # is too far forward on the frame. It should be able to be read once the fender is on, not covered up by it. Some body has stamped that on there.
|
Forum: Early V8 (1932-53)
10-16-2021, 07:07 PM
|
Replies: 1
Views: 637
`32 Ford late vs early features
Did all the "early" roadster doors have three side curtain snaps along the top of the door? Or did some of the early doors transition to the two snap style, same as the "later" doors. By "early"...
|
Forum: Early V8
09-24-2021, 02:21 PM
|
Replies: 0
Views: 383
|
Forum: Early V8
11-14-2020, 10:51 PM
|
Replies: 0
Views: 416
|
Forum: Early V8
09-23-2019, 07:29 PM
|
Replies: 0
Views: 910
|
Forum: Model-A
10-23-2018, 03:17 PM
|
Replies: 0
Views: 892
|
Forum: Model-A
10-23-2018, 03:10 PM
|
Replies: 0
Views: 904
|
Forum: Early V8
10-22-2018, 09:30 AM
|
Replies: 0
Views: 775
|
Forum: Model-A
10-08-2018, 08:17 PM
|
Replies: 0
Views: 957
|
Forum: Early V8
10-03-2018, 07:58 PM
|
Replies: 0
Views: 692
|
Forum: Early V8
10-03-2018, 04:37 PM
|
Replies: 0
Views: 735
|
Forum: Early V8
10-03-2018, 02:04 PM
|
Replies: 0
Views: 853
|
Forum: Early V8
09-11-2018, 09:02 PM
|
Replies: 0
Views: 995
|
Forum: Early V8
09-04-2018, 09:26 PM
|
Replies: 0
Views: 749
|
Forum: Early V8
09-03-2018, 08:19 PM
|
Replies: 0
Views: 661
|
Forum: Early V8 (1932-53)
02-06-2017, 04:50 PM
|
Replies: 31
Views: 7,177
|
Forum: Early V8 (1932-53)
09-22-2016, 11:12 AM
|
Replies: 30
Views: 8,321
Re: Brake Residual Valves
I wonder why we think a residue pressure valve is needed ? I don't think the stock `40 Ford hydraulics used them.
you will need to reduce from the 1/4" Ford brake line to go into the 3/16" fittings...
|
Forum: Early V8 (1932-53)
08-22-2016, 11:41 AM
|
Replies: 4
Views: 1,355
|
Forum: Early V8 (1932-53)
08-22-2016, 11:16 AM
|
Replies: 14
Views: 2,747
Re: Glass Packs
22" Smithy's from Speedway. I think they were their first product they sold back in 1952,
and I think they are still "made in America". At $ 40.00 each you can't beat the price. I just put a pair...
|
Forum: Early V8 (1932-53)
07-29-2016, 03:41 PM
|
Replies: 24
Views: 4,718
|
Forum: Early V8 (1932-53)
07-12-2016, 10:43 AM
|
Replies: 8
Views: 1,659
Re: 59AB in 32-Chatter rods
I recently put a 59a in my `32 chassis with a `39 type trans and stock `32 rear trans mount and "K" member, and stock pedals. And without any tension on the anti-chatter rods had the same problem. My...
|
Forum: Early V8 (1932-53)
04-15-2016, 01:37 PM
|
Replies: 6
Views: 1,857
Re: 32 rear spring
I have four `32 frames, that all have the kick up over the rear axle bashed in and swelled out by the rear axles bottoming out against them. This I would assume was caused with the stock springs in...
|
Forum: Early V8 (1932-53)
04-07-2016, 10:28 AM
|
Replies: 7
Views: 1,736
Re: Binding spindles on axle
Like Andy said, on `28 - `36 spindles " The tapered pin that goes thru the axle does in fact support the car entirely" Some years ago when I realized that, it seemed like a bad engineering design,...
|
Forum: Early V8 (1932-53)
04-07-2016, 10:09 AM
|
Replies: 55
Views: 19,128
Re: Torque tube seal-need a quick fix
Are you sure it's rear axle lube getting in the trans. ? That's a long way for lube to run uphill to get in the trans. I thought that front torque tube seal, just behind the speedo gear, was there...
|