Forum: Early V8
12-20-2022, 10:33 PM
|
Replies: 1
Views: 424
|
Forum: Early V8
12-15-2022, 01:44 PM
|
Replies: 1
Views: 424
1933 Ford BB Chassis Parts
I'm converting a 1933 BB to a pickup. I have chassis parts I wish to get rid of for free.
From a short wheelbase truck I have as pictured:
Front end
Rear end
Four speed trans
Drive line...
|
Forum: Model A (1928-31)
06-19-2021, 12:48 AM
|
Replies: 15
Views: 2,181
|
Forum: Model A (1928-31)
06-17-2021, 06:15 PM
|
Replies: 15
Views: 2,181
Re: Getting Oil to the Overhead Conversion
OK I'll follow that recommendations. Thanks. After considering everyone's input I think I'm going to reroute the the external line that feeds oil to the head. I'll post a picture as soon as I get it...
|
Forum: Model A (1928-31)
06-17-2021, 06:09 PM
|
Replies: 15
Views: 2,181
|
Forum: Model A (1928-31)
06-16-2021, 06:28 PM
|
Replies: 15
Views: 2,181
|
Forum: Model A (1928-31)
06-16-2021, 12:44 AM
|
Replies: 15
Views: 2,181
Re: Getting Oil to the Overhead Conversion
with 30psi input to the middle of the galley , the pressure measured at the rear of the galley is 4psi. The pressure at the front of the galley is not enough to travel up the 1/4" external line to...
|
Forum: Model A (1928-31)
06-15-2021, 06:21 PM
|
Replies: 15
Views: 2,181
|
Forum: Model A (1928-31)
06-15-2021, 02:07 AM
|
Replies: 15
Views: 2,181
Getting Oil to the Overhead Conversion
I have a (somewhat) stock B engine with a Steve Serr overhead conversion and a high volume oil pump that creates 30psi pressure to the galley after the full flow filter . Once the oil reaches the...
|
Forum: Model A (1928-31)
08-30-2020, 07:24 PM
|
Replies: 22
Views: 2,574
Re: Rod and Main Nuts
I just ordered a set also, thinking they were self locking but turns out they aren't. So just to be very clear about this. Are you installing them without any form of locking device? Do you stake...
|
Forum: Model A (1928-31)
05-29-2020, 10:14 PM
|
Replies: 2
Views: 1,502
|
Forum: Model A (1928-31)
05-28-2020, 07:43 PM
|
Replies: 2
Views: 1,502
Cragar Head is Cracked (Again) Can it be Fixed?
Took my cast iron Cragar head to be pressure tested and as I suspected it is cracked. It is leaking from the water jacket into the exhaust port from around the #2 and 3 exhaust guides. Anybody have...
|
Forum: Model A (1928-31)
03-27-2020, 11:41 AM
|
Replies: 16
Views: 3,054
Re: Is My Cam Going Flat?
Yes I agree with you and from my experience I believe the valve lash should decrease not increase. I would expect the valve lash to diminish once the lifter moves off the base circle.
Anyway, so far...
|
Forum: Model A (1928-31)
03-26-2020, 07:42 PM
|
Replies: 16
Views: 3,054
Re: Is My Cam Going Flat?
You are correct, is didn't explain this very well. I set it a .013 on the heel and rotated the crank in reverse about 180 degrees and check the clearance and it has grown to .025.
|
Forum: Model A (1928-31)
03-26-2020, 06:48 PM
|
Replies: 16
Views: 3,054
Is My Cam Going Flat?
I've got a rebuilt B block with a Cragar head. Virtually all of it is rebuilt or new including re-ground cam and new lifters. I've had a lot of break in problems with the side draft weber carb. I've...
|
Forum: Model A (1928-31)
02-23-2020, 09:03 PM
|
Replies: 9
Views: 2,045
|
Forum: Model A (1928-31)
02-20-2020, 01:48 PM
|
Replies: 9
Views: 2,045
|
Forum: Model A (1928-31)
01-03-2020, 03:15 PM
|
Replies: 2
Views: 1,027
|
Forum: Model A (1928-31)
01-03-2020, 01:17 PM
|
Replies: 2
Views: 1,027
28-29 Roadster Top Iron Corner Material
I can't seem to find any replacement tack strip material to go inside the 28-29 top irons. Does anyone have any suggestions for replacement material? Nobody seems to sell this stuff
|
Forum: Model T (1909-1927)
01-17-2018, 09:31 PM
|
Replies: 4
Views: 1,692
|
Forum: Model T (1909-1927)
01-17-2018, 02:00 PM
|
Replies: 4
Views: 1,692
|
Forum: Model T (1909-1927)
05-26-2017, 10:48 PM
|
Replies: 2
Views: 1,062
|
Forum: Model A (1928-31)
11-14-2016, 08:09 PM
|
Replies: 12
Views: 3,484
Re: crankshaft reconditioning Q...
Richard -
I'll drop the crocus cloth in the mail tomorrow and respond to your pm later tonight. And not to hijack your thread but since you did ask, here's a pic of the roadster, which like all...
|
Forum: Model A (1928-31)
11-13-2016, 11:36 AM
|
Replies: 12
Views: 3,484
|
Forum: Model A (1928-31)
08-06-2016, 07:29 PM
|
Replies: 14
Views: 3,935
|