Forum: Model A (1928-31)
05-11-2024, 11:05 AM
|
Replies: 12
Views: 425
Re: Tight crank gear
I always use a steel gear, a good, old, steel gear is better than a new cast iron gear.
|
Forum: Model A (1928-31)
05-10-2024, 11:08 AM
|
Replies: 12
Views: 425
Re: Tight crank gear
Heat the gear with a oxy/acet or blow torch. Heat it quite but not enough to show any color on it. It should then slip on, at least part way, then gently pound it on all the way. I made a driver...
|
Forum: Model A (1928-31)
05-04-2024, 12:45 PM
|
Replies: 6
Views: 858
Re: Not A, But Interesting
Very interesting! Makes me wonder how Ford and Dodge/Plymouth made their tubular axles in the late 30's? Chrysler also made one but it was a 3-piece unit with riveted on ends.
|
Forum: Model A (1928-31)
05-03-2024, 11:26 AM
|
Replies: 29
Views: 1,633
Re: Sticking valves?
I definitely recommend IMO but also think your rings may be worn, because the compression is slow but fine with oil added. Do the MMO first.
|
Forum: Model A (1928-31)
04-29-2024, 11:26 AM
|
Replies: 11
Views: 855
|
Forum: Model A (1928-31)
04-28-2024, 12:13 PM
|
Replies: 11
Views: 855
Re: Winfield Model M updraft carb
The difference between the S and the SR is that the later has an accelerator pump, not needed IMO. Gasket sets are available. Price depends on size, condition and are they complete with air-horn or...
|
Forum: Model A (1928-31)
04-27-2024, 11:36 AM
|
Replies: 7
Views: 915
Re: Side Water Outlet
The diamond is a genuine Ford part but cast by an outside foundry. That mark can be found on many Ford parts.
|
Forum: Model A (1928-31)
04-27-2024, 11:33 AM
|
Replies: 11
Views: 855
Re: Winfield Model M updraft carb
They were only used on T's. They are better than the stock T carb, but IMO a bit small for the Model A. I've run a few Winfield model S on my warmed up Model A, and really like them.
|
Forum: Model A (1928-31)
04-25-2024, 01:12 PM
|
Replies: 26
Views: 2,188
|
Forum: Model A (1928-31)
04-24-2024, 11:22 AM
|
Replies: 26
Views: 2,188
|
Forum: Model A (1928-31)
04-22-2024, 11:43 AM
|
Replies: 1,412
Views: 329,133
|
Forum: Model A (1928-31)
04-21-2024, 12:47 PM
|
Replies: 13
Views: 2,490
|
Forum: Model A (1928-31)
04-18-2024, 11:08 AM
|
Replies: 13
Views: 2,490
|
Forum: Model A (1928-31)
04-17-2024, 11:48 AM
|
Replies: 2
Views: 496
|
Forum: Model A (1928-31)
04-17-2024, 11:46 AM
|
Replies: 13
Views: 2,490
|
Forum: Model A (1928-31)
04-17-2024, 11:45 AM
|
Replies: 7
Views: 734
|
Forum: Model A (1928-31)
04-13-2024, 11:23 AM
|
Replies: 2
Views: 495
|
Forum: Model A (1928-31)
04-13-2024, 11:20 AM
|
Replies: 20
Views: 1,284
|
Forum: Model A (1928-31)
04-13-2024, 11:09 AM
|
Replies: 4
Views: 399
Re: '31 pickup rear fender filler panels
If yours is a late '31, it has narrower fenders and no fill panel. Late 31's have the fuel shut-off on the front side of the firewall, a dropped steering support, not attached to the gas tank, and a...
|
Forum: Late V8 (1954+)
04-12-2024, 11:11 AM
|
Replies: 0
Views: 384
Antique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Early V8 (1932-53)
04-12-2024, 11:10 AM
|
Replies: 1
Views: 228
Antique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Model T (1909-1927)
04-12-2024, 11:09 AM
|
Replies: 0
Views: 401
ntique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Model A (1928-31)
04-12-2024, 11:05 AM
|
Replies: 2
Views: 495
Antique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Model A (1928-31)
04-07-2024, 12:13 PM
|
Replies: 1,412
Views: 329,133
Re: tell a Model A related story
I mow with a 601 Ford tractor and tow a brand X mower. Both are old and worn out, like me, but they still work. I used to maintain our road with the tractor and a 7' blade but a neighbor does most...
|
Forum: Model A (1928-31)
04-06-2024, 12:16 PM
|
Replies: 5
Views: 642
Re: Model A hubs on V8 Axle?
Yes they can but the only advantage is the spring mounting. You can just make a bolt-on bracket to accomplish this.
|