Forum: Early V8 (1932-53)
05-10-2016, 09:39 AM
|
Replies: 3
Views: 1,092
|
Forum: Early V8 (1932-53)
05-10-2016, 09:35 AM
|
Replies: 3
Views: 1,092
|
Forum: Model A (1928-31)
04-24-2016, 07:42 AM
|
Replies: 37
Views: 6,995
Re: Float a motors
Is there a place to get replacement rubber? My car is missing the one at the trans.
|
Forum: Model A (1928-31)
04-24-2016, 07:34 AM
|
Replies: 70
Views: 15,221
|
Forum: Early V8 (1932-53)
03-04-2016, 02:08 AM
|
Replies: 10
Views: 1,158
|
Forum: Model A (1928-31)
03-04-2016, 02:01 AM
|
Replies: 5
Views: 1,828
Re: Chickashay
Is it worth the trip? Anyone know about how many vendors are usually there?
|
Forum: Model A (1928-31)
11-14-2015, 01:07 AM
|
Replies: 46
Views: 8,937
Re: help on overhaul failure
That sentence right there says a lot about your engine builder. As a former 2-stroke motorcycle racer who has seen a few seized cylinders, I can tell you that a piston seizure will not score the...
|
Forum: Model A (1928-31)
09-08-2015, 09:50 AM
|
Replies: 59
Views: 21,704
Re: Float-A-Motor mounts
I think my car may be missing this part. It has FAM mount at bellhousing and stock front mount.
|
Forum: Model A (1928-31)
08-21-2015, 02:54 AM
|
Replies: 15
Views: 4,111
Re: Steel wheels
Seems to be lots of confusion on this subject. Jim Brierley is correct. The necessary flat spacer is about .125" thick, and goes over the studs to leave a flat area for the back of the solid wheel to...
|
Forum: Early V8 (1932-53)
08-14-2015, 10:53 PM
|
Replies: 10
Views: 1,981
Re: 41 coupe exhaust
Duals would probably have to follow the path of the OG exhaust, then run the driver's side pipe back across the car somewhere near the rear crossmember or under the center of the X-member if you want...
|
Forum: Early V8 (1932-53)
08-14-2015, 05:19 PM
|
Replies: 10
Views: 1,981
Re: 41 coupe exhaust
I don't have pictures, and don't have a smartphone, but I have a 41 rolling chassis handy. The stock routing is from left side under oil pan, joining right side, and down the passenger side of the...
|
Forum: Early V8 (1932-53)
07-17-2015, 06:41 PM
|
Replies: 4
Views: 1,797
Re: 41 Ford gas tank installation
I just crawled under the 41 I am parting out to have a look. It's the same as bigdoor described. The bolts at the back are drilled and safety-wired.
|
Forum: Model A (1928-31)
06-02-2015, 10:47 AM
|
Replies: 19
Views: 4,764
Re: 15w-40
FYI: Zinc levels in Rotella T have been reduced below the ~1200 ppm level that's supposed to keep flat-tappet cams alive. SOMEWHERE I've saved a web page that shows the zddp levels of most major...
|
Forum: Model A (1928-31)
03-24-2015, 06:10 PM
|
Replies: 15
Views: 3,706
Re: Cracked heads
Must be. Buying a new head seems to be less of a gamble than a used one. I'm thinking I may end up with one of the new Winfield repro's that we've been seeing updates about. Out of four stock heads...
|
Forum: Model A (1928-31)
03-24-2015, 10:17 AM
|
Replies: 15
Views: 3,706
Cracked heads
Are ALL the heads for Model A's cracked? Seems like every one I find has cracks somewhere.
|
Forum: Early V8 (1932-53)
03-21-2015, 12:46 AM
|
Replies: 3
Views: 1,417
Re: Title help in TX
You'd think so. AFAIK, none of the County Tax Assessor/Collectors are actually doing these hearings. In my county, it's go bonded or go home. What's crappy is that the minimum value now for bonding...
|
Forum: Model A (1928-31)
03-21-2015, 12:06 AM
|
Replies: 33
Views: 7,477
Re: Torque wheels
hmmm...just so happens I got an ad in the paper with HF coupon for 9.95 torque wrenches. Might just have to go buy one or two.
|
Forum: Model A (1928-31)
02-15-2015, 11:23 AM
|
Replies: 42
Views: 9,287
|
Forum: Model A (1928-31)
02-14-2015, 10:55 PM
|
Replies: 42
Views: 8,482
Re: Again
Starts from the high-powered antibiotics they give you for surgery. Stuff darn near killed my wife.
|
Forum: Model A (1928-31)
02-14-2015, 10:53 PM
|
Replies: 16
Views: 4,519
|
Forum: Model A (1928-31)
01-29-2015, 11:26 PM
|
Replies: 30
Views: 6,840
Re: Shelf Life of Gasolene & other facts
No air space means no place for the vapors to expand into. We all have seen half-filled, sealed, plastic gas cans swell up like a balloon on a hot day, and crush in when it gets cold. Fill that same...
|
Forum: Model A (1928-31)
01-28-2015, 08:53 PM
|
Replies: 30
Views: 6,840
Re: Shelf Life of Gasolene & other facts
The reason ETOH gasoline doesn't last long is that it is hygroscopic. It attracts and absorbs moisture from that atmosphere. A SEALED container that's full (no air space) is the only effective way to...
|
Forum: Model A (1928-31)
01-25-2015, 06:05 PM
|
Replies: 12
Views: 4,367
|
Forum: Model A (1928-31)
01-25-2015, 05:57 PM
|
Replies: 62
Views: 31,083
|
Forum: Model A (1928-31)
01-24-2015, 05:21 PM
|
Replies: 12
Views: 4,367
|